1.To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.
2.Install this unit in a cool, dry, clean place – away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electrical shock, do not expose the unit to rain or water.
3.Never open the cabinet. If something drops into the set, contact your dealer.
4.Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power plug and the wires connected to other equipment. Never pull the wires themselves.
5.The openings on the cabinet assure proper ventilation of the unit. If these openings are obstructed, the temperature inside the cabinet will rise rapidly. Therefore, avoid placing objects against these openings, and install the unit in well- ventilated condition. Make sure to allow a space of at least 10 cm behind, 20 cm on the both sides and 30 cm above the top panel of the unit. Otherwise it may not only damage the unit, but also cause fire.
6.Always set the VOLUME control to
7.Do not attempt to clean the unit with chemical solvents; this might damage the finish. Use a clean, dry cloth.
8.Be sure to read the “TROUBLESHOOTING” section regarding common operating errors before concluding that the unit is faulty.
9.When not planning to use this unit for long periods of time (ie., vacation, etc.), disconnect the AC power plug from the wall outlet.
10.To prevent lightning damage, disconnect the AC power plug and disconnect the antenna cable when there is an electrical storm.
11.Grounding or polarization – Precautions should be taken so that the grounding or polarization of an appliance is not defeated.
12.AC outlet
Do not connect audio equipment to the AC outlet on the rear panel if that equipment requires more power than the outlet is rated to provide.
13.Voltage Selector (General Model only)
The voltage selector on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply.
Voltages are 110/120/220/240 V AC, 50/60 Hz.
This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off.
In this state, this unit is designed to consume a very small quantity of power.
IMPORTANT
Please record the serial number of this unit in the space below.
Serial No.:
The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
FOR CANADIAN CUSTOMERS
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT.
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE- CAUSING EQUIPMENT REGULATIONS.
FREQUENCY STEP switch (General Model only) Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (located at the rear) according to the frequency spacing in your area. Before setting this switch, disconnect the AC power plug of this unit from the AC outlet.
WARNING
Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE POWER SWITCH IS PRESSED
The IMPEDANCE SELECTOR switch may not be set to either end closely. If so, set the switch to either end closely.
IMPEDANCE SELECTOR
|
| IMPEDANCE SELECTOR |
| ||||
|
|
|
|
|
|
| |
|
|
|
| REAR | 6ΩMIN. /SPEAKER |
|
|
|
|
|
| CENTER | SINGLE:6ΩMIN. /SPEAKER |
|
|
|
|
|
|
| DUAL:3ΩMIN. /SPEAKER |
|
|
|
|
|
| MAIN | A OR B:4ΩMIN. /SPEAKER |
|
|
|
|
|
|
| A B:8ΩMIN. /SPEAKER |
|
|
|
|
|
| REAR | 8ΩMIN. /SPEAKER |
|
|
|
|
|
| CENTER | SINGLE:8ΩMIN. /SPEAKER |
|
|
|
|
|
|
| DUAL:4ΩMIN. /SPEAKER |
| MAINS |
|
|
|
| MAIN | A OR B:8ΩMIN. /SPEAKER |
| |
|
|
|
|
| A B:I6ΩMIN. /SPEAKER |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SWITCHED 
I20V 60Hz
I00W MAX. TOTAL
AC OUTLETS
(U.S.A. model)
4