CONNECTIONS

IMPEDANCE SELECTOR Switch

WARNING

Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise the unit may be damaged.

If this unit fails to turn on when STANDBY/ON is pressed, the IMPEDANCE SELECTOR switch may not be fully slide to either position. If so, slide the switch to either position fully when this unit is in the standby mode.

Select the right or left position according to the impedance of speakers in your system. Be sure to move this switch only when this unit is in the standby mode.

 

 

 

 

 

 

 

 

(Europe model)

If you use

left position

right position

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Center

The impedance must be 6 Ω

The impedance must be 8 Ω

IMPEDANCE

MAINS

 

 

 

 

 

 

speaker

or higher.

or higher.

SELECTOR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Rear

The impedance of each

The impedance of each

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

speakers

speaker must be 6 Ω or

speaker must be 8 Ω or

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

higher.

higher.

 

 

SET BEFORE POWER ON

 

 

100W MAX. TOTAL

 

 

If you use one pair of main

If you use one pair of main

 

MAIN A OR B : 4ΩMIN. /SPEAKER

 

 

 

SWITCHED

 

 

 

 

 

A + B : 8ΩMIN. /SPEAKER

 

 

 

 

 

 

 

 

 

 

 

speakers, the impedance of

speakers, the impedance of

 

CENTER : 6ΩMIN. /SPEAKER

 

 

 

 

 

 

 

 

 

 

 

 

REAR : 6ΩMIN. /SPEAKER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MAIN A OR B : 8ΩMIN. /SPEAKER

 

 

 

 

 

 

 

 

 

 

 

each speaker must be 4 Ω or

each speaker must be 8 Ω or

 

CENTER : 8ΩMIN. /SPEAKER

 

 

 

 

 

 

 

 

 

 

 

 

 

A + B : I6ΩMIN. /SPEAKER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REAR : 8ΩMIN. /SPEAKER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Main

higher.

higher.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

speakers

If you use two pairs of main

If you use two pairs of main

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

speakers, the impedance of

speakers, the impedance of

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

each speaker must be 8 Ω or

each speaker must be 16 Ω or

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

higher.

higher.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connecting the Power Supply Cords

AC OUTLETS (SWITCHED)

(Europe model)

MAINS

SET BEFORE POWER ON

100W MAX. TOTAL

 

 

SWITCHED

MAIN A OR B : 4ΩMIN. /SPEAKER

 

A + B : 8ΩMIN. /SPEAKER

 

CENTER

: 6ΩMIN. /SPEAKER

 

REAR

: 6ΩMIN. /SPEAKER

 

MAIN A OR B : 8ΩMIN. /SPEAKER

 

A + B : I6ΩMIN. /SPEAKER

 

CENTER

: 8ΩMIN. /SPEAKER

 

REAR

: 8ΩMIN. /SPEAKER

 

After completing all connections, connect the AC power cord to an AC power outlet. Disconnect the AC power cord if you will not use this unit for a long period of time.

Europe model ....................................................

2 OUTLETS

U.K. model ..........................................................

1 OUTLET

Use these outlets to connect the power cords from your components to this unit. The power to the AC OUTLET(S) is controlled by this unit’s STANDBY/ON (or POWER). These outlets will supply power to any connected component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the AC OUTLET(S) is 100 W.

To AC outlet

SWITCHED

16