Manuals / Brands / Home Audio / Stereo Receiver / Yamaha / Home Audio / Stereo Receiver

Yamaha RX-V520, RX-V420 TUNING, Connecting the Antennas, ■Connecting the indoor FM antenna, ■Connecting the AM loop antenna 3

1 69

Download 69 pages, 2.66 Mb

TUNING

Connecting the Antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength.

Connect each antenna correctly to the designated terminals.

FREQUENCY STEP switch (China and General

models only)
	STEP	Because the interstation frequency spacing
	FREQUENCY	differs in different areas, set the
	50KHZ	differs in different areas, set the
	50KHZ	FREQUENCY STEP switch (locating at the
	/9KHZ	FREQUENCY STEP switch (locating at the
	100KHZ
	/10KHZ	rear) according to the frequency spacing in
	FM/AM	rear) according to the frequency spacing in
		your area.
		North, Central and South America: 100 kHz/
		10 kHz
		Other area: 50 kHz/9 kHz
		Before setting this switch, disconnect the AC
		power plug of this unit from the AC outlet.

AM loop		Indoor FM
antenna		antenna
antenna		antenna
(included)		(included)
		(included)

TUNER

AM ANT GND							FM ANT

75UNBAL.

(U.S.A. model)

Ground (GND terminal)

For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

■Connecting the indoor FM antenna

Connect the included indoor FM antenna to the FM ANT 75Ω UNBAL. terminal.

Note

•Do not connect an outdoor FM antenna and the indoor FM antenna at the same time.

■Connecting the AM loop antenna 3 1

4	2	5

Antenna stand

1 Press and hold the tab to unlock the terminal hole.

2 Insert the AM loop antenna lead wires into the

AM ANT and GND terminals.

3 Release the tab to lock the lead wires.

Lightly pull the lead wires to confirm a good connection.

4 Attach the loop antenna to the antenna stand.

5 Orient the AM loop antenna so that the best reception is obtained.

y

•The AM loop antenna can be removed from the stand and attached to a wall, etc.

Notes

•The AM loop antenna should be placed away from this unit.

•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about the outdoor antennas.

26

Contents

Page SAFETY INSTRUCTIONS FCC INFORMATION (for US customers only) We Want You Listening For A Lifetime CAUTION: READ THIS BEFORE OPERATING YOUR UNIT CONTENTS FEATURES GETTING STARTED Checking the Package Contents Control Battery Replacement CONTROLS AND FUNCTIONS Front Panel Page Remote Control Using the Remote Control Display Rear Panel SPEAKER SETUP Speakers to Be Used ■Use of a subwoofer expands your sound field Speaker Placement ■Main speakers CONNECTIONS Before Connecting Components Connecting Audio Components ■Connecting to digital jacks ■Connecting a CD player ■Connecting an MD recorder, CD recorder or tape deck Connecting an External Decoder Page Connecting Video Components ■Audio signal jacks ■Video signal jacks ■ S VIDEO jacks RX-V520only ■VIDEO AUX jacks (on the front panel) Page Connecting Speakers ■Speaker cables ■Connecting to the MAIN SPEAKERS terminals ■Connecting to the REAR and CENTER SPEAKERS terminals ■Main speaker terminals ■Subwoofer connection IMPEDANCE SELECTOR Switch ■VOLTAGE SELECTOR (China and General models only) Connecting the Power Supply Cords ■AC OUTLETS (SWITCHED) ADJUSTING THE SPEAKER BALANCE Before You Start Adjusting Using the Test Tone Page PLAYING A SOURCE ■To mute the sound ■When you have finished using this unit ■Notes on the digital signal ■BGV (background video) function Input Modes and Indications ■Notes on playing a source encoded with a DTS signal Selecting a DSP Program ■On the remote control ■On the front panel ■Virtual CINEMA DSP and SILENT CINEMA off the effect speakers) TUNING Connecting the Antennas ■Connecting the indoor FM antenna ■Connecting the AM loop antenna 3 Automatic Tuning Manual Tuning Automatic Preset Tuning (for FM stations only) ■Automatic preset tuning options ■When automatic preset tuning is completed Manual Preset Tuning To Recall a Preset Station Exchanging Preset Stations RECORDING A SOURCE ■Special considerations when recording DTS software SET MENU Adjusting the Items on the SET MENU 1SPEAKER SET (speaker mode settings) ■CENTER SP (center speaker mode) ■MAIN SP (main speaker mode) ■REAR LR SP (rear speaker mode) ■BASS OUT (bass out mode) 2HP TONE CTRL (headphone tone control) 3 I/O ASSIGN ■3A (1) (for the OPTICAL OUTPUT jack) ■3B (2) to (4) (for the OPTICAL INPUT jacks) ■3C (5) (for the COAXIAL INPUT jack) 5 DOLBY D. SET (Dolby Digital set) ■LFE LEVEL ■D-RANGE(dynamic range) 6 DTS SET (DTS LFE level) 7 SP DLY TIME (center delay) 8DISPLAY SET ■DIMMER 9 MEM. GUARD (memory guard) DELAY TIME AND SPEAKER OUTPUT LEVELS Delay Time Sound Output Level of the Center Right Rear and Left Rear Speakers and Subwoofer Adjusting Method SLEEP TIMER Setting the SLEEP Timer Canceling the SLEEP Timer PRESET REMOTE CONTROL Component Selector Buttons Controlling the Components Connected to This Unit ■Example: To control YAMAHA CD player Description of Each Mode ■TAPE/MD MODE ■CD MODE ■DVD/LD MODE ■DVD MENU MODE ■ VCR MODE ■ CBL/SAT MODE ■TV MODE Setting the Manufacturer Code ■To use a second (and third) VCR Returning to the Factory Setting ■To return to the factory-setcodes in all modes ■To return to the factory-setcodes in each mode SOUND FIELD PROGRAM Hi-FiDSP Programs ■For audio sources: Nos. 1 to CINEMA DSP Programs ■For audio-videosources: Nos. 4 to ■For movie programs: Nos. 7 to ■MOVIE THEATER 1 and TROUBLESHOOTING ■ General Page Page ■Tuner ■Remote control SPECIFICATIONS (RX-V520) SPECIFICATIONS (RX-V420) GLOSSARY ■Dolby Surround ■Dolby Digital ■DTS (Digital Theater Systems) Digital Surround ■LFE 0.1 channel ■ S VIDEO signal RX-V520only ■PCM (Linear PCM) ■Sampling frequency and number of quantized bits RX-V520only ■I/O ASSIGN (SET MENU) INDEX LIST OF MANUFACTURER’S CODES LISTES DES CODES FABRICANT Page Page Page L Analog signal O Optical signal S Video signal Video signal Signal flow