Manuals / Brands / Home Audio / Stereo Receiver / Yamaha / Home Audio / Stereo Receiver

Yamaha RX-V520, RX-V420 Setting the Manufacturer Code, ■To use a second (and third) VCR

1 69

Download 69 pages, 2.66 Mb

Setting the Manufacturer Code

You can set the code for the manufacturer of your component after pressing the component selector buttons other than AMP(TUNER).

1 Turn on your component to be used.

2 Press one of the component selector buttons which corresponds to the component to be controlled.

3 Press both VOLUME buttons (u/d) at the same time for about four seconds.

The indicator flashes twice.

4 Use the numeric buttons to enter the four-digit manufacturer code for the component to be used. Make sure that the indicator flashes twice.

If the indicator does not flash, repeat step 3 and re-enter the code.

5 Press POWER (or any other button) on the remote control to check if you have set the code correctly.

If your component cannot be controlled with the remote control, try setting another code for the same manufacturer.

Notes

•You can set only one code for one mode.

•In the DVD/LD and DVD MENU modes:

Be sure to press DVD/LD on the component selector before entering the code for the DVD/LD player. You cannot set the code for a DVD player after pressing DVD MENU on the component selector. The code set in the DVD/LD mode is also simultaneously set in the DVD MENU mode.

•If your component does not respond to any of the codes listed for the manufacturer, use the original remote control supplied with your component.

PRESET REMOTE CONTROL

■To use a second (and third) VCR

You can control a second (and third) VCR in the CBL/SAT and DVD MENU modes if a cable TV or satellite tuner, or DVD player is not being used.

Note

•In order to set a second (and third) VCR in the DVD MENU mode, it is necessary to first set up the code for an LD player in the DVD/LD mode.

1 Turn on the VCR to be used.

2 Press CBL/SAT or DVD

MENU on the component selector.

3 Press both VOLUME buttons (u/d) at the same time for about four seconds.

The indicator flashes twice.

4 Use the numeric buttons to enter the four-digit code for the second (and third) VCR. Make sure that the indicator flashes twice.

If the indicator does not flash, repeat step 3 and re-enter the code.

5 Press POWER (or any other button) on the remote control to check if you have set the code correctly.

If the VCR cannot be controlled with the remote control, try setting another code for the same manufacturer.

ADVANCEDOPERA TION

English

45

Contents

Page SAFETY INSTRUCTIONS FCC INFORMATION (for US customers only) We Want You Listening For A Lifetime CAUTION: READ THIS BEFORE OPERATING YOUR UNIT CONTENTS FEATURES GETTING STARTED Checking the Package Contents Control Battery Replacement CONTROLS AND FUNCTIONS Front Panel Page Remote Control Using the Remote Control Display Rear Panel SPEAKER SETUP Speakers to Be Used ■Use of a subwoofer expands your sound field Speaker Placement ■Main speakers CONNECTIONS Before Connecting Components Connecting Audio Components ■Connecting to digital jacks ■Connecting a CD player ■Connecting an MD recorder, CD recorder or tape deck Connecting an External Decoder Page Connecting Video Components ■Audio signal jacks ■Video signal jacks ■ S VIDEO jacks RX-V520only ■VIDEO AUX jacks (on the front panel) Page Connecting Speakers ■Speaker cables ■Connecting to the MAIN SPEAKERS terminals ■Connecting to the REAR and CENTER SPEAKERS terminals ■Main speaker terminals ■Subwoofer connection IMPEDANCE SELECTOR Switch ■VOLTAGE SELECTOR (China and General models only) Connecting the Power Supply Cords ■AC OUTLETS (SWITCHED) ADJUSTING THE SPEAKER BALANCE Before You Start Adjusting Using the Test Tone Page PLAYING A SOURCE ■To mute the sound ■When you have finished using this unit ■Notes on the digital signal ■BGV (background video) function Input Modes and Indications ■Notes on playing a source encoded with a DTS signal Selecting a DSP Program ■On the remote control ■On the front panel ■Virtual CINEMA DSP and SILENT CINEMA off the effect speakers) TUNING Connecting the Antennas ■Connecting the indoor FM antenna ■Connecting the AM loop antenna 3 Automatic Tuning Manual Tuning Automatic Preset Tuning (for FM stations only) ■Automatic preset tuning options ■When automatic preset tuning is completed Manual Preset Tuning To Recall a Preset Station Exchanging Preset Stations RECORDING A SOURCE ■Special considerations when recording DTS software SET MENU Adjusting the Items on the SET MENU 1SPEAKER SET (speaker mode settings) ■CENTER SP (center speaker mode) ■MAIN SP (main speaker mode) ■REAR LR SP (rear speaker mode) ■BASS OUT (bass out mode) 2HP TONE CTRL (headphone tone control) 3 I/O ASSIGN ■3A (1) (for the OPTICAL OUTPUT jack) ■3B (2) to (4) (for the OPTICAL INPUT jacks) ■3C (5) (for the COAXIAL INPUT jack) 5 DOLBY D. SET (Dolby Digital set) ■LFE LEVEL ■D-RANGE(dynamic range) 6 DTS SET (DTS LFE level) 7 SP DLY TIME (center delay) 8DISPLAY SET ■DIMMER 9 MEM. GUARD (memory guard) DELAY TIME AND SPEAKER OUTPUT LEVELS Delay Time Sound Output Level of the Center Right Rear and Left Rear Speakers and Subwoofer Adjusting Method SLEEP TIMER Setting the SLEEP Timer Canceling the SLEEP Timer PRESET REMOTE CONTROL Component Selector Buttons Controlling the Components Connected to This Unit ■Example: To control YAMAHA CD player Description of Each Mode ■TAPE/MD MODE ■CD MODE ■DVD/LD MODE ■DVD MENU MODE ■ VCR MODE ■ CBL/SAT MODE ■TV MODE Setting the Manufacturer Code ■To use a second (and third) VCR Returning to the Factory Setting ■To return to the factory-setcodes in all modes ■To return to the factory-setcodes in each mode SOUND FIELD PROGRAM Hi-FiDSP Programs ■For audio sources: Nos. 1 to CINEMA DSP Programs ■For audio-videosources: Nos. 4 to ■For movie programs: Nos. 7 to ■MOVIE THEATER 1 and TROUBLESHOOTING ■ General Page Page ■Tuner ■Remote control SPECIFICATIONS (RX-V520) SPECIFICATIONS (RX-V420) GLOSSARY ■Dolby Surround ■Dolby Digital ■DTS (Digital Theater Systems) Digital Surround ■LFE 0.1 channel ■ S VIDEO signal RX-V520only ■PCM (Linear PCM) ■Sampling frequency and number of quantized bits RX-V520only ■I/O ASSIGN (SET MENU) INDEX LIST OF MANUFACTURER’S CODES LISTES DES CODES FABRICANT Page Page Page L Analog signal O Optical signal S Video signal Video signal Signal flow