SECTION 3: ASSEMBLING YOUR LAWN MOWER

To Remove Unit From Carton

•Remove staples, break glue on top flaps, or cut tape at carton end and peel along top flap to open carton.

•Remove loose parts included with your unit (i.e., operator’s manual, etc.).

•Cut along corners and lay carton down flat. Remove packing material.

•Roll or slide unit out of carton.

IMPORTANT: This unit is shipped without gasoline. Make sure to service engine with gasoline and oil as instructed in the separate engine manual before operating your mower.

NOTE: Reference to right or left side of the mower is observed from the operating position.

Tools Required

Pair of pliers (not necessary, but helpful)

Disconnect Spark Plug Wire

•Disconnect spark plug wire from the spark plug and attach rubber boot to a bolt on the engine to ground. See Figure 1.

Rubber Boot

Spark Plug

Figure 1

Attaching Handle

•Pull up and back on the upper handle to raise the handle into the operating position. Make certain the lower handle is seated securely into the handle mounting brackets. Tighten the hand knobs on each side of the handle (carriage bolts and saddle washers must be seated properly into the handle as shown). See Figure 2.

NOTE: Your mower is shipped with the handle in the higher height position. If you wish to lower the height of the handle, refer to the instructions for handle height adjustment on page 10.

Carriage Bolt

 

 

 

 

Saddle

Upper

 

 

 

Washer

 

 

 

 

Handle

 

 

 

Lower

 

 

 

 

 

 

 

 

Handle

 

 

 

Hand

 

 

 

 

 

 

Knob

Saddle Washer

Figure 2

•Remove the hairpin clips from the outer holes in the weld pins on the handle mounting brackets.

•Using a pair of pliers, squeeze one leg of the lower handle against the handle mounting bracket. Insert the hairpin clip into the inner hole on the weld pin.

See Figure 3. Repeat on other side.

Hairpin

Clip in

Inner Hole

Weld

Pin

Lower

Handle

Handle

Mounting

Bracket

Figure 3

Attaching Starter Rope

•The rope guide is attached to the right side of the upper handle. Loosen the wing nut which secures the rope guide. For location of the wing nut, see Figure 4.

Insert starter rope into

 

rope guide

Wing Nut

 

Rope

Guide

Figure 4

•With the spark plug wire disconnected and grounded, hold the blade control handle against the

7

Page 6 Page 8
Page 7
Image 7
Yard-Man 573 manual Assembling Your Lawn Mower
Page 6 Page 8

573 specifications

The Yard-Man 573 lawnmower is a remarkable piece of outdoor equipment that offers both power and efficiency for homeowners seeking a dependable tool for maintaining their lawns. With its robust design and thoughtful engineering, the Yard-Man 573 stands out in the crowded market of residential lawn maintenance.

One of the key features of the Yard-Man 573 is its reliable engine. Equipped with a durable gas engine, it delivers ample horsepower to handle various grass types and challenging terrains. This engine ensures consistent performance, even under demanding conditions, allowing users to tackle their mowing tasks with confidence.

The Yard-Man 573 boasts a wide cutting deck, typically around 21 inches, which enhances its ability to cover more ground in less time. This size not only speeds up the mowing process but also provides a clean and even cut. The cutting height can be easily adjusted to cater to different grass lengths and seasonal changes, giving users the flexibility to maintain their lawn as per their preference.

User comfort and convenience are also prioritized in the design of the Yard-Man 573. It features an ergonomic handle that is adjustable, allowing users of different heights to operate the mower comfortably. The foldable handle mechanism makes storage a breeze, saving space in the garage or shed.

Another technological advancement integrated into the Yard-Man 573 is its efficient grass collection system. The mower is equipped with a rear bagger, which effectively collects clippings, minimizing the cleanup effort after mowing. This feature not only helps keep the lawn tidy but also allows for easy disposal of clippings, whether for composting or waste collection.

Safety is a critical aspect of lawnmowers, and the Yard-Man 573 does not disappoint. It is designed with safety features such as a blade brake that stops the blades when the user releases the handle, preventing accidents. Additionally, the mower's sturdy build and reliable materials contribute to longevity and resilience.

In summary, the Yard-Man 573 combines power, efficiency, and user-friendly features to create a lawnmower that meets the demands of both seasoned landscapers and first-time homeowners alike. With its advanced engineering and thoughtful design, it is poised to provide a reliable solution for maintaining a beautiful lawn year after year.
Top Page Image Contents