ADJUSTMENTS

MOTION CONTROL LINKAGE ADJUSTMENT:

1.This adjustment must be made with the drive wheels rotating. Raise rear of the unit and block it up so the wheels are free to rotate. CAUTION: Keep hands, feet and clothing away from rotating tires.

2.Tilt seat forward and remove the seat rod from seat so the seat can rotate down onto the frame. Make sure the seat is adjusted toward the rear of the unit so it clears the controls on the console.

3.Place a 2x4 board approximatly 10 to 12 inches long between the foot plate and the center of the seat to engage the seat safety switch. NOTE: You may want to cover the end of the 2x4 with a rag to protect the seat from marring.

4.The reverse spring detent must be adjusted correctly before the motion control linkages may be adjusted.(See reverse spring detent adjustment section.)

5.Loosen the nuts directly behind each ball joint on both rods that connect the pump arm to the motion control assemblies. (See Fig 5 )

6.Start the engine. The park brake must be engaged and the motion control levers must be in the neutral slot (See figure 6 page10) to start the engine. Run engine at approximately 1/

2throttle.

7.Release park brake to allow wheels to rotate. CAUTION: Keep hands, feet and clothing away from rotating tires.

8.Begin with either side and put the motion control lever into the neutral position. Adjust the motion control linkage by rotating the double nuts on the rod in the proper direction until the wheel stops rotating (See Fig 5 ).

Move the motion control lever forward then into the neutral position and place it into the neutral slot. The wheel must be stopped completely at this point. Now do the same in reverse and release the lever. The lever should return to neutral on its own. If not see reverse spring detent adjustment section.

9.Run engine at full throttle to make sure wheels do not rotate. Readjust if any rotation occurs.

10.Repeat on the opposite side and tighten nuts against ball joints.

11.Remove the 2x4 board and make sure the seat wiring is connected to the wiring harness. WARNING: Seat must be connected for safety interlock system to properly function.

OPERATING INSTRUCTIONS

CONTROLS:

1.Be thoroughly familiar with all controls their function and how to operate them before operating the mower.

2.Motion control levers located on each side of the console control direction of movement. The left lever controls the flow of oil from the left hydro pump to the left wheel motor. The right lever controls the flow of oil from the right hydro pump to the right wheel motor.

10

Page 9 Page 11
Page 10
Image 10
Yazoo/Kees ZKH52222, ZKH52252, ZKH61252 Adjustments Motion Control Linkage Adjustment, Operating Instructions Controls
Page 9 Page 11

ZKH61252, ZKH52222, ZKH52252 specifications

The Yazoo/Kees ZKH61252, ZKH52222, and ZKH52252 are advanced, high-performance machines designed for landscaping, grass care, and other turf management tasks. These models embody the combination of durability, efficiency, and user-friendliness that the Yazoo/Kees brand is renowned for.

One of the standout features across these models is their powerful engines, which provide reliable performance and robust torque. Powered by industry-leading engines, the ZKH series ensures that operators can tackle even the most challenging terrains with ease. The ZKH61252, with its higher horsepower, is particularly suited for large commercial properties and demanding landscaping projects, while the ZKH52222 and ZKH52252 are perfect for residential lawns and smaller tasks without sacrificing power or efficiency.

The innovative cutting deck design is another hallmark of the ZKH series. These mowers feature advanced mulching technology, which finely chops grass clippings and redistributes them evenly back onto the lawn. This not only enhances the aesthetics of the lawn but also supports healthy growth by returning nutrients to the soil. The cutting height adjustment system is precise and user-friendly, allowing operators to achieve the perfect cut for various grass types and conditions.

Ergonomics and operator comfort have not been overlooked in the ZKH series. The models feature plush, contoured seats that reduce fatigue during extended mowing sessions. The intuitive control layout ensures that operators can easily fine-tune settings without having to divert their attention from the task at hand. Additionally, the ZKH series incorporates vibration-dampening technology, which further enhances ride comfort, making it easier for operators to navigate rough terrains.

In terms of technology, the ZKH61252, ZKH52222, and ZKH52252 integrate advanced features such as zero-turn capabilities, allowing for exceptional maneuverability around obstacles, flower beds, or trees. This increases productivity and reduces mowing time, making these machines invaluable for both professional landscapers and homeowners.

Durability is also a key characteristic of the Yazoo/Kees ZKH series. With a robust frame construction and high-quality materials, these mowers are built to withstand the rigors of regular use. The maintenance-friendly design ensures that routine servicing can be accomplished quickly and easily, maximizing uptime.

In summary, the Yazoo/Kees ZKH61252, ZKH52222, and ZKH52252 represent a blend of power, efficiency, comfort, and advanced technology. Suitable for both commercial and residential applications, these machines deliver exceptional performance and a premium mowing experience, making them an excellent choice for any landscaping enthusiast.
Top Page Image Contents