MAINTENANCE

1.Engine oil level: Check daily with engine cold and on a flat surface. Remove the dipstick and wipe clean. Reinsert the dipstick all the way. Remove the dipstick and check oil level. If oil level is low remove oil fill cap and add oil. Use engine manufacturers specs for type of oil.

2.Pump drive belt compartment: Stop engine and remove key. Tilt seat forward and lift rubber flap. Clean all debris from inside. Inspect rubber flap for proper fit and replace if needed. NOTE: Cleaning may need to be done more frequently in dry conditions.

3.Mower blades: Stop engine and remove key. Lift deck into the transport position and in- spect blades. Sharpen or replace as needed. Check daily or more often if needed. The machine requires more power with dull blades and gives a poor cut. If blades get bent, replace them. Blades shouldn’t have any notches from hitting objects. The air foil on top of the blade should be sufficient to raise the grass for cutting. If blades are in good condition, sharpen at an angle of 22 to 28 degrees about 2-1/2 inches in from the tips. Note: After sharpening, check blades for proper balance, if needed correct balance to prevent excessive vibration.

4.Safety interlock system: Check daily and never operate the mower if this system is not functioning properly. The starter should crank only when the operator is in the seat, the park brake set, blades off and the motion control levers in the neutral slots. If the mower starts with any of these controls on or in an operating position, turn the mower off and repair the system immediately.

5.Hardware: Stop engine and remove key thoroughly inspect the entire machine for any missing or loose hardware. Check daily.

6.Air cleaner: Stop engine and remove key. Remove plastic cover and loosen wingnut on the air cleaner. Remove the foam pre-cleaner and wash or replace if needed. Inspect paper filter and replace if dirty. Check every 25 hours, daily if in very dirty conditions. Fuel efficiency, engine RPM, and available power goes down rapidly if the air filter is dirty. Prolonged effects could damage the engine.

7.Engine oil: Change oil to manufacturers specifications. Stop engine and remove key. Drain oil when engine is warm. Thoroughly clean around cap before removing. Remove oil drain cap from the end of drain hose located at the right rear of unit allow to drain and replace drain cap. Remove oil filter and replace. Put a light coat of clean oil on the filter gasket before installing. Fill engine with oil using manufacturers specs, see specification sheet. The factory

uses Quaker State Super Blend 10w-30. Start engine and idle slowly to allow the oil to recoat the interior of the engine and then inspect for leaks.

8.Hydraulic oil: Check daily. Stop engine and tilt seat forward.Thoroughly clean around cap. Remove cap. Oil level should be 1/4” to 1” below the neck of the tank. If not, add oil. NOTE: Use

13

Page 12 Page 14
Page 13
Image 13
Yazoo/Kees ZKH52222, ZKH52252, ZKH61252 important safety instructions Maintenance
Page 12 Page 14

ZKH61252, ZKH52222, ZKH52252 specifications

The Yazoo/Kees ZKH61252, ZKH52222, and ZKH52252 are advanced, high-performance machines designed for landscaping, grass care, and other turf management tasks. These models embody the combination of durability, efficiency, and user-friendliness that the Yazoo/Kees brand is renowned for.

One of the standout features across these models is their powerful engines, which provide reliable performance and robust torque. Powered by industry-leading engines, the ZKH series ensures that operators can tackle even the most challenging terrains with ease. The ZKH61252, with its higher horsepower, is particularly suited for large commercial properties and demanding landscaping projects, while the ZKH52222 and ZKH52252 are perfect for residential lawns and smaller tasks without sacrificing power or efficiency.

The innovative cutting deck design is another hallmark of the ZKH series. These mowers feature advanced mulching technology, which finely chops grass clippings and redistributes them evenly back onto the lawn. This not only enhances the aesthetics of the lawn but also supports healthy growth by returning nutrients to the soil. The cutting height adjustment system is precise and user-friendly, allowing operators to achieve the perfect cut for various grass types and conditions.

Ergonomics and operator comfort have not been overlooked in the ZKH series. The models feature plush, contoured seats that reduce fatigue during extended mowing sessions. The intuitive control layout ensures that operators can easily fine-tune settings without having to divert their attention from the task at hand. Additionally, the ZKH series incorporates vibration-dampening technology, which further enhances ride comfort, making it easier for operators to navigate rough terrains.

In terms of technology, the ZKH61252, ZKH52222, and ZKH52252 integrate advanced features such as zero-turn capabilities, allowing for exceptional maneuverability around obstacles, flower beds, or trees. This increases productivity and reduces mowing time, making these machines invaluable for both professional landscapers and homeowners.

Durability is also a key characteristic of the Yazoo/Kees ZKH series. With a robust frame construction and high-quality materials, these mowers are built to withstand the rigors of regular use. The maintenance-friendly design ensures that routine servicing can be accomplished quickly and easily, maximizing uptime.

In summary, the Yazoo/Kees ZKH61252, ZKH52222, and ZKH52252 represent a blend of power, efficiency, comfort, and advanced technology. Suitable for both commercial and residential applications, these machines deliver exceptional performance and a premium mowing experience, making them an excellent choice for any landscaping enthusiast.
Top Page Image Contents