Electrical connections
Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations.
THIS COOKER MUST BE EARTHED.
The manufacturer declines any liability should these safety measures not be observed.
This cooker is designed to be connected to a 230V 50Hz AC electrical supply.
Before switching on, make sure the electricity supply voltage is the same as that indicated on the cooker rating plate. The rating plate is located on the oven frame.
The cooker is supplied without supply cord. A 3 core flexible supply cord must be fitted, in accordance with the specification given in the relevant tables.
1) Loosen the two fixing screws securing the back protective screen of the cooker, then lift it up and remove it. This will expose the terminal block on the right bottom corner.
2)Loosen the two cable clamp screws and lift the top section of the clamp enough to allow the cable to be passed through.
3)Connect the red (live) wire to the terminal which is marked with the letter "L".
4)Connect the black (neutral) wire to the terminal which is marked with the letter "N".
5)After fitting a green or yellow/green sleeve over the bare copper wire (earth wire), connect the exposed end to the terminal which is marked with the earth symbol 
or with the letter "E"coloured green and yellow.
NOTE:
The earth wire should be about 2 cm longer than the live and neutral wires.
6)Secure the cable by means of the clamp screws and refit the back protective screen.
The cooker should be connected to a double pole switch with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch should be sited within 2m from the cooker and easily accessible upon completion of the installation.
The switch must not break the yellow and green earth cable at any point. The earth wire should be about 2 cm longer than the live and neutral wires.
Ensure that the hob supply cable does not come into contact with surfaces with temperatures higher than 50 deg. C.
Supply Cable Specifications
For Uk use only
Connection | Min. size | Cable / flex | Fuse | |||||||||||
via | Cable/flex | type |
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• Cooker | 6 mm2 | H05 | 30 A | |||||||||||
Control |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Circuit |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For Europe use only |
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Min. size Cable/flex | Cable / flex type |
| Fuse | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
3x 2.5 mm2 |
|
|
|
| H05 |
| 30 A | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
FO 2375
19
