Before using your dishwasher for the

first time:

1. Ensure that the electrical and water connections comply with
the installation instructions
2. Remove all packaging from inside the appliance
3. Set the water softener
4. Pour 1 litre of water inside the salt container and then fill with
salt
5. Fill the rinse aid dispenser.
6. Run a "Rinse and Hold" programme.

Setting the water softener

The dishwasher is equipped with a water softener designed to
remove minerals and salts from the water supply, which would
have a detrimental or adverse effect on the operation of the
appliance.
The higher the content of these salts, the harder your water is.
Water hardness is measured in equivalent scales, Clarke,
French degrees and PPM (parts per Million).
The softener should be adjusted according to the hardness of
the water in your area. Your local Water Authority can advise you
on the hardness of the water in your area.
The dishwasher is factory set at level 4.
If this level is not suitable for your area the softener should be
adjusted.
If your water is level 0 it is already soft and therefore there
is no need to use salt.
In this case adjust the water softener on level 1 without
using salt.
Only for dishwasher models with salt refill
indicator light:
if the water softener has been adjusted on level 1 without use of
salt, the salt refill indicator light on the control panel will always
remain illuminated when the machine is switched on.
Each push button corresponds to a different level:
Level 1 = programme push button 1
Level 2 = programme push button 2
Level 3 = programme push button 3
Level 4 = programme push button 4
Level 5 = programme push button 5
The adjustment of the water softener is possible only with
the machine in setting mode.

To select a different level, proceed as follows:

1.Press the ON/OFF push button and then press and keep
pressed simultaneously for about 5 seconds the push
buttons 3 and 5.
The indicator light corresponding to the current level flashes.
2.Press the programme push button corresponding to the
required level.
3.5 seconds after having last pressed any of the programme
push buttons, the dishwasher memorises the level selected
and returns to the programme setting mode.

Filling with salt

Attention!
Only use salt specifically designed for use in dishwashers.
All other types of salt not specifically designed for use in
dishwasher, especially table salt, will damage the water
softener.
Only fill with salt just before starting a washing programme.
This will prevent any grains of salt or salty water, which
may have been spilled, remaining on the bottom of the
machine, which may cause corrosion.

To fill:

1. To fill with salt, unscrew the cap of the salt container.
2. Pour 1 litre of water inside the container (this is necessary
only before filling with salt for the first time).
3. Using the funnel (if
provided), pour in the salt
until the container is full.
Do not worry if water over
flows from the unit when
filling with salt, this is quite
normal.
4. Replace the cap making
sure that there is no trace of
salt on the screw thread or
on the gasket.
5. Screw on the cap tightly.
The salt container will require topping up periodically.
According to the model, an indicator reminds you when filling
with salt:
A) The salt cap has a refill
indicator window in the
centre. Agreen float is clearly
visible when there is salt
inside the container, and
almost disappears when the
salt has finished reminding
you to add salt.
B) A salt indicator light on the control panel will come on when
the salt has finished.
The salt indicator light on the control panel can remain
illuminated for 2-6 hours after the salt has been replenished,
assuming the dishwasher remains switched on. If you are
using salts that take longer to dissolve then this can take
longer.
The function of the machine is not affected.
2
Before use
Level Use of
salt
French
degrees
(°TH)
PPM
(Parts per
Million)
Clarke
degrees
0
1
2
3
4
5
NO
YES
YES
YES
YES
YES
0 - 6
7 - 14
15 - 28
29 - 42
43 - 56
57 - 63
0 - 8
9 - 20
21 - 40
41 - 60
61 - 80
81 - 90
0 - 80
81 - 200
201 - 400
401 - 600
601 - 800
801 - 900
Water hardness
SR11
SALE
SALT
SALZ
SEL
SR06
SO322