Zenoah BC530WE, BC3500LE/WE, BC3500WE, BC2300LE, BC4500WE, BC2610LE/WE, BC2310LE Use, Maintenance

5 Use

■STARTING THE ENGINE

Take care that the cutting head will start rotating upon the engine starts.

A: EXCEPT BC530WE

1.Push the primer pump(1) several times until overflown fuel flows out in the clear tube.

2.Move the choke lever(2) to the closed position.

B: BC530WE

1-1.Open the fuel shutoff valve. (1)

1-2.While pushing the tickler lever(3), push the primer pump(2) several times until the flow of fuel into the overflow pipe.

2.Move the choke lever(4) to the closed position.

3.A: BC2310LE/BC2610LE/WE BC3500WE/BC4500WE/BC530WE

Set the engine switch(a) to the " I " position. Set the throttle lever to the start position (1- 2-3).

■STOPPING THE ENGINE

1. Release the throttle lever.

2. Move the engine switch to the "O" position.

BC2610WE

BC2310LEBC3500WE

BC2610LEBC4500WE

2

1 BC3500LE

BC530WE

■ADJUSTMENTS

•Throttle cable: The normal play is 1 or 2 mm when measured at the carburetor side end. Readjust with the cable adjuster(1) as re- quired.

•Engine idling speed: It is normal that the engine keeps running without the blade rotation, when the throttle lever is released. When the engine speed is too high or too slow, readjust the idle set screw (2).

BC2310LE/BC2610LE/WE

BC3500LE/WE/BC4500WE

BC530WE

■LINE HEAD USAGE

WARNING

1.Always wear eye protection such as safety goggles. Never lean over the rotating cutting head. Rocks or other debris could be thrown into eyes and face and cause serious personal injury.

2.Keep the debris guard attached in place at all times when the unit is operated.

TRIMMING GRASS AND WEEDS

•Always remember that the TIP of the line does cutting. You will achieve better results by not crowding the line into the cutting area. Allow the unit to trim at its own pace.

1.Hold the unit so the head is off the ground and is tilted about 20 degrees toward the sweep direction.

2.Use full throttle when cutting.

3.You can avoid thrown debris by sweeping from your left to the right.

4.Use a slow, deliberate action to cut heavy growth. The rate of cutting motion will depend on the material being cut. Heavy growth will require slower action than will light growth.

5.Never swing the unit so hard as you are in danger of losing your balance or control of the unit.

6.Try to control the cutting motion with the hip rather than placing the full workload on the arm and hands.

7.Take precautions to avoid wire, grass and dead, dry, long-stem weeds from wrapping around the head shaft. Such materials can stall the head and cause the clutch to slip, resulting in damage to the clutch system if repeated frequently.

ADJUSTING THE LINE LENGTH

BC2310LE

BC2610LE

BC530WE

■CUTTING WORK

• Your brushcutters is equipped with a semi-

auto type nylon line head that allows the

operator to advance the line without

stopping the engine. When the line

becomes short, lightly tap the head on the

ground while running the engine at full

throttle.

• Each time the head is bumped, the line

advance about 1 inch(25.4 mm). For better

BC2610WE

BC3500WE

BC4500WE

B: BC3500LE

While pulling the throttle lever (1,2), set the engine switch(a) to the “I (START)” position

and release the
throttle. Then		1
the	throttle a
lever is in to the
“start position”.

2 BC3500LE

4.Place the unit on a flat, firm place. Keep the cutting head clear of everything around it.

5.While holding the unit firmly, pull out the starter rope quickly.

6.After the engine has started, open the choke guradually and allow the engine to warm up. Pull the throttle lever to unlock it.

•By using the shoulder strap, hang the unit on your right side. Adjust the strap length so that the cutting head may become parallel to the ground.

•Choose a suitable recommended cutting attachment according to the object to be cut. Never use other cutting attachment not approved by ZENOAH.

effect, tap the head on bear ground or hard

soil. Avoid bumping in thick, tall grass as

the engine may stall by overload.

6 Maintenance

Before cleaning, inspecting, or repairing the unit, make sure that the engine has stopped and is cool.

■REFILLING TRIMMING LINE

1.For replacement line, use a diameter of 2.4 mm. The spool is capable for a line upto 6 m on the 4" head. Avoid using a larger line as it may cut down the trimming performance.

2.Pinch the slotted area on the both sides of the spool housing to unhook the bottom cap.

3.Take out the spool and pull off the old line. Put one end of new line through the spool holes and pull it until the length is equal between each part of the line.

4.Wind up the line in the correct direction as indicated on the spool.

5.Hook each end of the line in the slot on the edge of the spool, and then put the ends through the eyelets on the housing.