3 Setup
■ENGINE
•Using attached 4 socket screws, secure the connection firmly with equal force.
■HANDLE
1.Loosen the 4 bolts on the upper cap and insert the handles equally. Retighten the bolts.
2.Put the handle assembly into the bracket and put the upper cap over it. Tighten the cap securely.
■PROTECTOR
Wrap the protector around the outer pipe as shown in the figure, and fasten the magic fastener.
(1) Protector
■BLADE GUARD
Attach the guard on the outer pipe. Fix it with 2 bolts.
■INSTALLING BLADE
Remove the guard skirt of debris guard, when using metal blade.
1.Put the angled bar(1) into the side holes of the inner holder and the gearcase.
2.Remove the
3.Put the blade onto the inner holder(2). Make the marked side face the holder.
4.Put the outer holder(3) onto the gearshaft making the recessed side face the blade.
5.Fasten the blade by the nut.
■BALANCE UNIT
1.Put on strap and attach unit to strap.
2.Slide clamp up or down until unit balances with head aparting from the ground when using it.
4 Fuel
WARNING
•Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m (10ft) away from the fueling point before starting the engine.
RECOMMENDED MIXING RATIO
GASOLINE 50:OIL 1
(when using ZENOAH genuine oil)
•The Zenoah engines are lubricated by oil specially formulated for
•Do not use BIA or TCW
•Exhaust emission are controlled by the fundamental engine parameters and components (eq., carburation, ignition timing and port timing) without addition of any major hardware or the introduction of an inert material during combustion.
•These engines are certified to operate on unleaded gasoline.
•Make sure to use gasoline with a minimum octane number of 89 RON (USA/Canada: 87AL)
•If you use a gasoline of a lower octane value than prescribed, there is a danger that the engine temperature may rise and an engine problem such as piston seizing may consequently occur.
•Unleaded gasoline is recommended to reduce the contamination of the air for the sake of your health and the environment.
•Poor quality gasolines or oils may damage sealing rings, fuel lines or fuel tank of the engine.
■HOW TO MIX FUEL
IMPORTANT
Pay attention to agitation.
1.Measure out the quantities of gasoline and oil to be mixed.
2.Put some of the gasoline into a clean, approved fuel container.
3.Pour in all of the oil and agitate well.
4.Pour In the rest of gasoline and agitate again
for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture.
5.Put a clear indication on the outside of the container to avoid mixing up with gasoline or other containers.
6.Indicate the contents on outside of container for easy identification.
■FUELING THE UNIT
1.Untwist and remove the fuel cap. Rest the cap on a dustless place.
2.Put fuel into the fuel tank to 80% of the full capacity.
3.Fasten the fuel cap securely and wipe up any fuel spillage around the unit.
WARNING
1.Select bare ground for fueling.
2.Move at least 10feet (3meters) away from the fueling point before starting the engine.
3.Stop the engine before refueling the unit. At that time, be sure to sufficiently agitate the mixed gasoline in the container.
FOR YOUR ENGINE LIFE, AVOID;
1.FUEL WITH NO OIL(RAW GASOLINE) – It will cause severe damage to the internal engine parts very quickly.
2.GASOHOL – It can cause deterioration of rubber and/or plastic parts and disruption of engine lubrication.
3.OIL FOR
4.Mixed fuels which have been left unused for a period of one month or more may clog the carburetor and result in the engine failing to operate properly.
5.In the case of storing the product for a long period of time, clean the fuel tank after rendering it empty. Next, activate the engine and empty the carburetor of the composite fuel.
6.In the case of scrapping the used mixed oil container, scrap it only at an authorized repository site.
NOTE
As lot details of quality assurance, read the description in the section Limited Warranty carefully. Moreover, normal wear and change in product with no functional influence are not covered by the warranty. Also, be careful that, if the usage in the instruction manual is not observed as to fhe mixed gasoline, etc. described therein, if may not be covered by the warranty.
5 Operation
■STARTING ENGINE
WARNING
The cutting head will start rotating upon the engine starts.
1.Feed fuel into the fuel tank and tighten the cap securely.
