
StudSensor™ Pro
with AC WireWarning™ and
SpotLite® Pointing System
WORKING WITH DIFFERENT MATERIALS
StudSensor Pro
11⁄2 in. (38 mm) of common construction materials in DeepScan mode, three pri- mary factors can affect sensing depth: thickness, density, and moisture content.
StudSensor Pro
The Zircon StudSensor™ Pro
to continuously detect hot AC voltage in both modes.
INSTALLING THE BATTERY
1 | Squeeze sides of |
| clip to help |
release clip end. | |
2 | Slide |
| into compartment, |
terminal side first, matching (+) and
SpotLite® Pointing System
Stud Edge Groove
TruCal®
LED
StudScan | STUD SCAN | DEEPSCAN | Stud DeepScan® |
|
| ||
Mode LED |
|
| Mode LED |
On/Off Button |
|
| Mode Switch |
When the top green LED is lit, a steady
tone sounds, and the SpotLite® shines, you have located the edge of the stud. Mark this spot.
•Bare wood flooring (in DeepScan mode)
•Linoleum on wood base
•Gypsum drywall over plywood sheathing
•Wallpapered walls (if dry)
•Textured ceilings if uniform thickness (Place a thin piece of cardboard on ceiling and scan through it to avoid damage
to texturing.)
StudSensor Pro
•Ceramic floor tile
•Carpeting and padding
•Wallpaper with metallic fibers
•Freshly painted walls that are still damp (must dry at least a week)
•Lath and plaster walls
•Foil covered insulation board
FCC Part 15 Class B Registration Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pur- suant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guar- antee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be deter- mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
(1)Reorient or relocate the receiving antenna.
(2)Increase the separation between the equipment and receiver.
(3)Connect the equipment into an outlet on a circuit, different from that which the receiver is connected (if applicable).
3 | Replace the clip. |
| Battery will last |
approximately two years under normal conditions.
CALIBRATION AND SCANNING IN STUD SCAN OR DEEPSCAN® MODES
Note: Unit calibrates on each use.
Use Stud Scan Mode for depths to about 3⁄4 in. (19 mm) and DeepScan for depths up to
11⁄2 in. (38 mm) or double layers.
Note: Keep unit flat against wall. Do not lift or tilt unit during calibration or scanning.
4 | Slide the Mode Selector |
| switch to the desired |
scanning mode. The mode can | |
be selected with the unit on | |
or off. | |
5 | With StudSensor Pro |
| turned off, position the unit |
flat against the wall. | |
6 | Without moving unit, squeeze |
| and hold On/Off button. |
TruCal® LED should be lit. | |
7 | Continue to hold |
| in the On/Off |
button then slowly slide | |
unit horizontally across | |
the wall, right or left. | |
8 | As you begin to approach a stud, the red LEDs |
| will light successively, from bottom to top. |
10 Continue scanning beyond marked
spot until green LED goes out. Slide unit in reverse direction to locate other edge of stud.
11 Mark this second spot. Middle of stud
is centered between the two marks.
CONTINUOUS AC VOLTAGE DETECTION (WireWarning™)
12 The StudSensor Pro
AC in a hot electrical wire. The voltage detection feature works continuously in both Stud Scan and DeepScan modes. When sensing voltage, the small AC light comes on.
Caution: The StudSensor Pro
OPERATING CAUTIONS
13 | Depending on the proximity of electrical wiring |
| or pipes to the wall surface, the scanner may |
detect them in the same manner as studs. Caution should always be used when nailing, cutting, or drilling in walls, floors, and ceilings that may contain these items.
To avoid surprises, remember that studs or joists are normally spaced 16 in. (406 mm) or 24 in. (610 mm) apart and are 11⁄2 in. (38 mm) in width. Anything closer together or a different width may not be a stud, joist, or firebreak. Always turn off the power when working near electrical wires.
(4)Consult the dealer or an experienced radio/TV technician for help.
HELPFUL HINTS
Situation | Probable Causes | Solutions |
Lights start flashing and | • Scan began on dense part of | • Turn unit off, move over a few inches, press On/Off button, |
unit starts beeping. | wall or over a stud. | and start again. |
| • Unit not flat against wall. | • On rough surfaces, place piece of paper on wall, scanning |
| • Unit tilted or lifted during scan. | through it to help slide unit more smoothly. |
| (All these factors affect proper | • Keep hand at least 6 in.(152 mm) from StudSensor |
| calibration.) | Pro |
|
| thumb and index finger no higher than handgrips. Be |
|
| careful not to move your fingers after calibration. |
|
| • Always hold unit parallel to and move perpendicular to |
|
| object you’re trying to locate. |
|
|
|
Center green LED doesn’t | • Wall is particularly thick or | • Interpret red LED closest to center as stud edge. |
light in Stud Scan mode. | dense. | • Switch to DeepScan to locate the stud. |
|
|
|
The green TruCal LED | • Unit may not be flat against | • Hold unit so two Velcro™ strips on the back make |
lights but, when scan- | the wall. | contact with wall. |
ning, unit doesn't do | • If it is in the DeepScan mode | • Recalibrate unit in a different place and rescan area. |
anything else. | (the DeepScan LED is lit), you |
|
| may have calibrated over a stud. |
|
|
|
|
All three red LEDs and | • Scanning surface is too dense | • If you are using unit on a recently taped, painted, or |
green LED light at the | or too wet for unit to operate. | wallpapered wall, allow time to dry and try again. |
same time and unit |
|
|
beeps continuously. |
|
|
|
|
|
Working in DeepScan | • You may have calibrated over | • Move StudSensor Pro |
mode and can’t detect | a stud. (The error condition is | and recalibrate. |
studs. | disabled in DeepScan mode |
|
| because it is twice as sensitive |
|
| as Stud Scan.) | • Hold unit so two Velcro™ strips on the back make |
| • You may be holding the unit | |
| like a TV remote, aiming it at | contact with wall. |
| the wall. |
|
|
|
|
Detects other objects | • Electrical wiring and metal or | • Remember that studs or joists are normally spaced 16 in. |
besides studs. | plastic pipes may be near or | (406 mm) or 24 in. (610 mm) apart and are 11⁄2 in. |
| touching back surface of wall. | (38 mm) wide. |
|
| • Always turn off power when cutting, nailing, or drilling |
|
| near electrical wires. |
|
|
|
You suspect electrical | • Wires may be shielded behind | • See above solution. |
wires, but do not | metallic wall coverings, | • Use extra caution if the area has plywood, thick wood |
detect any. | plywood shearwall or other | backing behind drywall, or |
| dense material, or in conduit; | • If a switch controls an outlet, make sure it is ON for |
| StudSensor Pro | detection, but turned off when working near electrical wires. |
| be able to find them. |
|
| • The wires may not be hot. |
|
| • Wires may be too deep to sense. |
|
|
|
|
Area of voltage detection | • Static charge may develop on | • To narrow detection, turn unit off and on again at the edge |
is too large. | drywall, spreading voltage | of where wire was detected and scan again. |
| detection as much as 12 in. |
|
| (305 mm) from each side of |
|
| an actual electrical wire. |
|
|
|
|
Questions? Check our Web site at www.zircon.com and click “Support.”