Setting the mapping for I/O scanning | Schneider Electric LXM32M

LXM32M			5 Commissioning


Parameter name	Description	Unit	Data type	Parameter address
HMI menu		Minimum value	R/W	via fieldbus
HMI name		Factory setting	Persistent
		Maximum value	Expert

EthIPmaster1	IP address master, byte 1	-	UINT16	CANopen 3044:29h
	IP address of the master that is permitted to	0	UINT16	Modbus 17490
	IP address of the master that is permitted to	0	UINT16	Profibus 17490
	perform Modbus TCP I/O scanning.	255	UINT16	CIP 168.1.41
	If set to 0.0.0.0 (default), any master can	255	UINT16	CIP 168.1.41
	If set to 0.0.0.0 (default), any master can		R/W
	perform I/O scanning.		R/W
	perform I/O scanning.		per.
			per.
	Setting can only be changed if power stage		-
	is disabled.
	Changed settings become active immedi-
	ately.

EthIPmaster2	IP address master, byte 2	-	UINT16	CANopen 3044:2Ah
	Setting can only be changed if power stage	0	UINT16	Modbus 17492
	Setting can only be changed if power stage	0	UINT16	Profibus 17492
	is disabled.	255	UINT16	CIP 168.1.42
		255	UINT16	CIP 168.1.42
	Changed settings become active immedi-		R/W
	ately.		per.
			-

EthIPmaster3	IP address master, byte 3	-	UINT16	CANopen 3044:2Bh
	Setting can only be changed if power stage	0	UINT16	Modbus 17494
	Setting can only be changed if power stage	0	UINT16	Profibus 17494
	is disabled.	255	UINT16	CIP 168.1.43
		255	UINT16	CIP 168.1.43
	Changed settings become active immedi-		R/W
	ately.		per.
			-

EthIPmaster4	IP address master, byte 4	-	UINT16	CANopen 3044:2Ch
	Setting can only be changed if power stage	0	UINT16	Modbus 17496
	Setting can only be changed if power stage	0	UINT16	Profibus 17496
	is disabled.	255	UINT16	CIP 168.1.44
		255	UINT16	CIP 168.1.44
	Changed settings become active immedi-		R/W
	ately.		per.
			-

5.7.3Setting the mapping for I/O scanning

The input mapping is set by means of the parameters

EthOptMapInp1 ... EthOptMapInp3.

The output mapping is set by means of the parameters

EthOptMapOut1 ... EthOptMapOut3.

▶Set the desired mapping values with the parameters

EthOptMapInp1 ... EthOptMapInp3 and EthOptMapOut1 ...

EthOptMapOut3.

0198441113843, V1.01, 01.2012

Modbus-TCP module

47

Image 47

Schneider Electric LXM32M manual Setting the mapping for I/O scanning

Contents

LXM32M Important information Table of contents Diagnostics and troubleshooting Accessories and spare parts LXM32M About this manual Further reading Fieldbus products on the network Introduction LXM32M Intended use Before you begin safety informationQualification of personnel Hazard categories Basic information Standards and terminology Bus topology BasicsModbus TCP technology Function principle Client / server model Network service Snmp Structure of a Modbus message Modbus TCP protocol Field Length Description Mbap header Connection management Modbus TCP communication Excep Name Description Tion Code Modbus response to a Modbus request Address Value Reading and writing parameters 4 I/O scanning to Drive Profile Lexium Byte Meaning Data type Parameter address 4.1 I/O scanning Output Bit Meaning 4.2 I/O scanning Input Inputs Bit Signal Factory setting Parameter channel Ctrl Subindex Index Field Bytes Value Meaning Modbus services Function CodeFunction Code 3 Read Multiple Registers Sub-function Code Diagnostics function Function Code 8 Diagnostics Function Code 16 Write Multiple Registers Function Code 23 ReadWrite Multiple Registers Object ID Object name Value Function Code 43 Encapsulated Interface Transport Example of Function Code Examples LXM32M Description Order no InstallationInstallation of the module Pin Signal Meaning Electrical installation Commissioning the device Commissioning Switching on the device Power stage supply is switched off First Setup Dhcp / dhcP Dhcp Bootp / boot BootpManual assignment of the network address Manual / MAnu Manual IP address Ethernet module, byte Assignment of the network address via Bootp Assignment of the network address via Dhcp Setting the protocol Setting the transmission rate Set the IP address of the gateway with the parameters Setting the gateway Master with Word Swap Activating I/O scanning Setting I/O-ScanningSetting the master for I/O scanning Setting the mapping for I/O scanning PLC Setting communication monitoring for I/O scanning Setting the web server 0198441113843, V1.01 Operation Bit Name Meaning Operating statesIndication of the operating state Bit Name Meaning Operating state Changing the operating state Bit Name Description Indicating and monitoring the operating modeOperating modes Bit Name Description Starting and changing an operating mode MODE+ACTION Overview of operating modes Operating mode Jog Operating mode Electronic Gear 24 h Operating mode Profile Torque 23 h Operating mode Profile Velocity Operating mode Profile Position Operating mode Homing LXM32M6 Operation Operating mode Motion Sequence Web server Extended settings User interface Main menu Submenu Content FTP server Accessing the FTP server FDR service Fast Device Replacement LXM32M Fieldbus communication error diagnostics Diagnostics and troubleshooting Color Status Meaning Status LEDs Meaning for EtherNet/IP Meaning for Modbus TCP Color Error indication Excep Name Description Tion Code LXM32M Cables Accessories and spare parts LXM32M Units and conversion tables Glossary Moment of inertia TemperatureRotation Torque Terms and Abbreviations LXM32M Index LXM32M