Husqvarna YTH2242T To Start Engine See Fig, Purge Transmission, Automatic Transmission Warm UP

Page 12

OPERATION

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 3)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating position, depress brake pedal and set parking brake.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to fast position

•Pull choke control out for a cold engine start attempt. For a warm engine start attempt the choke control may not be needed.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, push choke control in, wait a few minutes and try again. If engine still does not start, pull the choke control out and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50° F and below)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the engine to accept small changes in speed and load, until the choke control is fully in. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Release the parking brake and let the brake slowly return to operating position.

•Allow one minute for transmission to warm up.This can be done during the engine warm up period.

•The attachments can be used during the engine warm-up period after the transmission has been warmed up and may require the choke control be pulled out slightly.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is run-

ning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

•Place tractor safely on a level surface - that is clear and open - with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. Dis- engage parking brake

CAUTION: At any time, during step 4, there may be movement of the drive wheels.

•Depress forward drive pedal to full forward position, hold for five (5) seconds and release pedal. Depress reverse drive pedal to full reverse position, hold for five

(5) seconds and release pedal. Repeat this procedure three (3) times.

•Shut- off engine and set parking brake.

•Engage transmission by placing freewheel control in engaged position (See “TO TRANSPORT” in this sec- tion of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. Disengage parking brake.

•Drive tractor forward for approximately five feet then backwards for five feet. Repeat this driving procedure three times.

Your transmission is now purged and now ready for normal operation.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 917.279180 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Assembly Unassembled PartsTo Remove Tractor from Carton Unpack CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor StoppingTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigSystem Characteristics To Operate MowerService REMINDER/HOUR Meter Before Starting the EngineTo Operate on Hills Check Engine OIL LevelTo Start Engine See Fig Purge TransmissionAutomatic Transmission Warm UP Mowing Tips Maintenance Lubrication ChartBefore Each USE Battery TractorBrake Operation TiresEngine Cleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigsTo Remove Mower See Fig To Level Mower Mower Drive Belt Installation To Replace Mower Drive Belt See FigMower Drive Belt Removal To Replace Motion Drive Belt See Fig To Check BrakeFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb Interlocks and RelaysTo Remove Hood and Grill Assembly See Fig To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model Number YTH2242TElectrical KEY Part NO. NO.DESCRIPTION Chassis KEY Part NO. noKEY Part Description Steering Assembly Drive Tractor - Model Number YTH2242T Spark Arrester KIT EngineMower Lift Seat Assembly Decals Wheels and TiresMower Deck KEY Part NO. NO. Description 900 170431 Spring Clip, Housing 178783 Bearing, Ball 178784 Tractor - Model Number Briggs Engine Model Number 441777, Type Number 0284-E1Carburetor Gasket SET Valve Gasket SET KEY Part Description Repair Parts Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

YTH2242T specifications

The Husqvarna YTH2242T is a powerful and versatile riding lawn mower designed for homeowners who seek an efficient and reliable solution for maintaining their lawns. With a robust 24 HP Briggs & Stratton engine, this mower offers the perfect balance of power and durability, ensuring that you can tackle even the toughest mowing tasks with ease.

One of the standout features of the YTH2242T is its 42-inch cutting deck. This size strikes a perfect balance between maneuverability and coverage, allowing users to navigate through tight spaces while still achieving an efficient mowing radius. The deck is made from high-quality materials, designed to resist wear and tear over time, ensuring longevity and dependability.

The YTH2242T employs a hydrostatic transmission, offering seamless speed and direction control without the need for manual shifting. This technology not only enhances the ease of use but also provides a smooth and enjoyable driving experience. Operators can focus on the mowing process rather than worrying about gear changes.

Another significant characteristic is the ergonomic design of the operator's station. The high-back seat ensures comfort during extended periods of use, while the adjustable control levers allow operators to customize their position for optimal comfort and control. Additionally, its compact size makes it easy to store and maneuver in smaller yards, enhancing the overall user experience.

Husqvarna has incorporated the innovative Air Induction Mowing Technology into the YTH2242T, which enhances grass lift and ensures a consistent cut in various mowing conditions. This technology ensures that the mower can handle tough grasses and uneven terrains without compromising the quality of the cut.

Safety features are paramount in the design of the YTH2242T. The mower is equipped with a safety switch that automatically shuts off the engine when the operator leaves the seat, reducing the risk of accidents. Furthermore, the reinforced frame adds stability and durability, ensuring that the mower can withstand rigorous use.

In summary, the Husqvarna YTH2242T combines power, technology, and thoughtful design to deliver an exceptional mowing experience. Its impressive features, including a strong engine, hydrostatic transmission, ergonomic controls, and advanced mowing technology, make it an ideal choice for homeowners looking for performance and reliability in their lawn care equipment. Whether you are maintaining a small yard or a larger landscape, the YTH2242T stands out as a dependable partner for all your mowing needs.
Top Page Image Contents