Husqvarna YTH2242T Replacing Battery See Fig, To Start Engine with a Weak Battery See Fig

Page 22

SERVICE AND ADJUSTMENTS

Replace washers and snap retaining ring securely in axle groove.

Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 28

REPLACING BATTERY (See Fig. 30)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent spark- ing from accidental grounding.

Lift hood to raised position.

Disconnect BLACK battery cable (A) then RED battery cable and carefully remove battery from tractor.

Install new battery with terminals in same position as old battery.

First connect RED battery cable (B) to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover (C) over terminal.

Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely

Close hood.

TO START ENGINE WITH A WEAK BATTERY (See Fig. 29)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

C

Positive B (Red) Cable

ANegative (Black) Cable

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

BLACK cable first from chassis and then from the fully charged battery.

RED cable last from both batteries.

WEAK OR DEAD

FULLY CHARGED

BATTERY

BATTERY

02954

FIG. 30

TO REPLACE HEADLIGHT BULB

Raise hood.

Pull bulb holder out of the hole in the backside of the grill.

Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

FIG. 29

22

Image 22
Contents 917.279180 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor StoppingSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelPurge Transmission To Start Engine See FigAutomatic Transmission Warm UP Mowing Tips Lubrication Chart MaintenanceBefore Each USE Brake Operation BatteryTractor TiresEngine Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig To Level Mower To Replace Mower Drive Belt See Fig Mower Drive Belt InstallationMower Drive Belt Removal Front Wheel TOE-IN/CAMBER To Replace Motion Drive Belt See FigTo Check Brake To Remove Wheel for Repairs See FigTo Replace Headlight Bulb Replacing Battery See FigTo Start Engine with a Weak Battery See Fig Interlocks and RelaysTo Adjust Choke Control To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model Number YTH2242TElectrical KEY Part NO. NO.DESCRIPTION KEY Part NO. no ChassisKEY Part Description Steering Assembly Drive Tractor - Model Number YTH2242T Spark Arrester KIT EngineMower Lift Seat Assembly Decals Wheels and TiresMower Deck KEY Part NO. NO. Description 900 170431 Spring Clip, Housing 178783 Bearing, Ball 178784 Tractor - Model Number Briggs Engine Model Number 441777, Type Number 0284-E1Carburetor Gasket SET Valve Gasket SET KEY Part Description Repair Parts Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

YTH2242T specifications

The Husqvarna YTH2242T is a powerful and versatile riding lawn mower designed for homeowners who seek an efficient and reliable solution for maintaining their lawns. With a robust 24 HP Briggs & Stratton engine, this mower offers the perfect balance of power and durability, ensuring that you can tackle even the toughest mowing tasks with ease.

One of the standout features of the YTH2242T is its 42-inch cutting deck. This size strikes a perfect balance between maneuverability and coverage, allowing users to navigate through tight spaces while still achieving an efficient mowing radius. The deck is made from high-quality materials, designed to resist wear and tear over time, ensuring longevity and dependability.

The YTH2242T employs a hydrostatic transmission, offering seamless speed and direction control without the need for manual shifting. This technology not only enhances the ease of use but also provides a smooth and enjoyable driving experience. Operators can focus on the mowing process rather than worrying about gear changes.

Another significant characteristic is the ergonomic design of the operator's station. The high-back seat ensures comfort during extended periods of use, while the adjustable control levers allow operators to customize their position for optimal comfort and control. Additionally, its compact size makes it easy to store and maneuver in smaller yards, enhancing the overall user experience.

Husqvarna has incorporated the innovative Air Induction Mowing Technology into the YTH2242T, which enhances grass lift and ensures a consistent cut in various mowing conditions. This technology ensures that the mower can handle tough grasses and uneven terrains without compromising the quality of the cut.

Safety features are paramount in the design of the YTH2242T. The mower is equipped with a safety switch that automatically shuts off the engine when the operator leaves the seat, reducing the risk of accidents. Furthermore, the reinforced frame adds stability and durability, ensuring that the mower can withstand rigorous use.

In summary, the Husqvarna YTH2242T combines power, technology, and thoughtful design to deliver an exceptional mowing experience. Its impressive features, including a strong engine, hydrostatic transmission, ergonomic controls, and advanced mowing technology, make it an ideal choice for homeowners looking for performance and reliability in their lawn care equipment. Whether you are maintaining a small yard or a larger landscape, the YTH2242T stands out as a dependable partner for all your mowing needs.