Husqvarna YTH2242T owner manual To Replace Motion Drive Belt See Fig, To Check Brake

Page 21

SERVICE AND ADJUSTMENTS

S

M

R

R

FIG. 26

TO REPLACE MOTION DRIVE BELT (See Fig. 27)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

Disconnect clutch wire harness (A).

Remove anti-rotation link (B) on right side of tractor.

Remove belt from stationary idler (C) and clutching idler (D).

Remove belt from centerspan idler (E).

Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades (F).

Remove belt downward from engine pulley and around electric clutch (G).

Slide belt toward rear of tractor, off the steering plate

(H) and remove from tractor.

BELT INSTALLATION -

Install new belt from tractor rear to front, over the steer- ing plate (H) and above clutch brake pedal shaft (J).

Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley (G).

Pull belt toward rear of tractor. Carefully work belt down around transmission cooling fan and onto the input pulley (F). Be sure belt is inside the belt keeper.

Install belt on centerspan idler (E).

Install belt through stationary idler (C) and clutching idler (D).

Reinstall anti-rotation link (B) on right side of tractor. Tighten securely.

Reconnect clutch harness (A).

Make sure belt is in all pulley grooves and inside all belt guides and keepers.

Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

G

H

B

A

C

J

D

E

F

02953 electric

FIG. 27

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 28)

Block up axle securely.

Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

Repair tire and reassemble.

On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

21

Image 21
Contents 917.279180 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Unassembled Parts AssemblyTo Remove Tractor from Carton Unpack CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Reverse Operation System ROS on Position Know Your TractorStopping HOW to USE Your TractorTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigSystem Characteristics To Operate MowerBefore Starting the Engine Service REMINDER/HOUR MeterTo Operate on Hills Check Engine OIL LevelTo Start Engine See Fig Purge TransmissionAutomatic Transmission Warm UP Mowing Tips Maintenance Lubrication ChartBefore Each USE Tractor BatteryBrake Operation TiresEngine Muffler CleaningSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigsTo Remove Mower See Fig To Level Mower Mower Drive Belt Installation To Replace Mower Drive Belt See FigMower Drive Belt Removal To Check Brake To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable To Remove Hood and Grill Assembly See FigTo Adjust Choke Control To Adjust CarburetorOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Tractor - Model Number YTH2242T SchematicElectrical KEY Part NO. NO.DESCRIPTION Chassis KEY Part NO. noKEY Part Description Steering Assembly Drive Tractor - Model Number YTH2242T Engine Spark Arrester KITMower Lift Seat Assembly Wheels and Tires DecalsMower Deck KEY Part NO. NO. Description 900 170431 Spring Clip, Housing 178783 Bearing, Ball 178784 Briggs Engine Model Number 441777, Type Number 0284-E1 Tractor - Model NumberCarburetor Gasket SET Valve Gasket SET KEY Part Description Repair Parts Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

YTH2242T specifications

The Husqvarna YTH2242T is a powerful and versatile riding lawn mower designed for homeowners who seek an efficient and reliable solution for maintaining their lawns. With a robust 24 HP Briggs & Stratton engine, this mower offers the perfect balance of power and durability, ensuring that you can tackle even the toughest mowing tasks with ease.

One of the standout features of the YTH2242T is its 42-inch cutting deck. This size strikes a perfect balance between maneuverability and coverage, allowing users to navigate through tight spaces while still achieving an efficient mowing radius. The deck is made from high-quality materials, designed to resist wear and tear over time, ensuring longevity and dependability.

The YTH2242T employs a hydrostatic transmission, offering seamless speed and direction control without the need for manual shifting. This technology not only enhances the ease of use but also provides a smooth and enjoyable driving experience. Operators can focus on the mowing process rather than worrying about gear changes.

Another significant characteristic is the ergonomic design of the operator's station. The high-back seat ensures comfort during extended periods of use, while the adjustable control levers allow operators to customize their position for optimal comfort and control. Additionally, its compact size makes it easy to store and maneuver in smaller yards, enhancing the overall user experience.

Husqvarna has incorporated the innovative Air Induction Mowing Technology into the YTH2242T, which enhances grass lift and ensures a consistent cut in various mowing conditions. This technology ensures that the mower can handle tough grasses and uneven terrains without compromising the quality of the cut.

Safety features are paramount in the design of the YTH2242T. The mower is equipped with a safety switch that automatically shuts off the engine when the operator leaves the seat, reducing the risk of accidents. Furthermore, the reinforced frame adds stability and durability, ensuring that the mower can withstand rigorous use.

In summary, the Husqvarna YTH2242T combines power, technology, and thoughtful design to deliver an exceptional mowing experience. Its impressive features, including a strong engine, hydrostatic transmission, ergonomic controls, and advanced mowing technology, make it an ideal choice for homeowners looking for performance and reliability in their lawn care equipment. Whether you are maintaining a small yard or a larger landscape, the YTH2242T stands out as a dependable partner for all your mowing needs.