Husqvarna YTH2242T To Adjust Mower Cutting Height See Fig, To Adjust Gauge Wheels See Fig

Page 10
FIG.9

OPERATION

J

K

L

FIG. 7

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

FIG. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

10

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attachment lift lever.

2.Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield (S) in place.

S

FIG. 10

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 917.279180 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor StoppingSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelPurge Transmission To Start Engine See FigAutomatic Transmission Warm UP Mowing Tips Lubrication Chart MaintenanceBefore Each USE Brake Operation BatteryTractor TiresEngine Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig To Level Mower To Replace Mower Drive Belt See Fig Mower Drive Belt InstallationMower Drive Belt Removal Front Wheel TOE-IN/CAMBER To Replace Motion Drive Belt See FigTo Check Brake To Remove Wheel for Repairs See FigTo Replace Headlight Bulb Replacing Battery See FigTo Start Engine with a Weak Battery See Fig Interlocks and RelaysTo Adjust Choke Control To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model Number YTH2242TElectrical KEY Part NO. NO.DESCRIPTION KEY Part NO. no ChassisKEY Part Description Steering Assembly Drive Tractor - Model Number YTH2242T Spark Arrester KIT EngineMower Lift Seat Assembly Decals Wheels and TiresMower Deck KEY Part NO. NO. Description 900 170431 Spring Clip, Housing 178783 Bearing, Ball 178784 Tractor - Model Number Briggs Engine Model Number 441777, Type Number 0284-E1Carburetor Gasket SET Valve Gasket SET KEY Part Description Repair Parts Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

YTH2242T specifications

The Husqvarna YTH2242T is a powerful and versatile riding lawn mower designed for homeowners who seek an efficient and reliable solution for maintaining their lawns. With a robust 24 HP Briggs & Stratton engine, this mower offers the perfect balance of power and durability, ensuring that you can tackle even the toughest mowing tasks with ease.

One of the standout features of the YTH2242T is its 42-inch cutting deck. This size strikes a perfect balance between maneuverability and coverage, allowing users to navigate through tight spaces while still achieving an efficient mowing radius. The deck is made from high-quality materials, designed to resist wear and tear over time, ensuring longevity and dependability.

The YTH2242T employs a hydrostatic transmission, offering seamless speed and direction control without the need for manual shifting. This technology not only enhances the ease of use but also provides a smooth and enjoyable driving experience. Operators can focus on the mowing process rather than worrying about gear changes.

Another significant characteristic is the ergonomic design of the operator's station. The high-back seat ensures comfort during extended periods of use, while the adjustable control levers allow operators to customize their position for optimal comfort and control. Additionally, its compact size makes it easy to store and maneuver in smaller yards, enhancing the overall user experience.

Husqvarna has incorporated the innovative Air Induction Mowing Technology into the YTH2242T, which enhances grass lift and ensures a consistent cut in various mowing conditions. This technology ensures that the mower can handle tough grasses and uneven terrains without compromising the quality of the cut.

Safety features are paramount in the design of the YTH2242T. The mower is equipped with a safety switch that automatically shuts off the engine when the operator leaves the seat, reducing the risk of accidents. Furthermore, the reinforced frame adds stability and durability, ensuring that the mower can withstand rigorous use.

In summary, the Husqvarna YTH2242T combines power, technology, and thoughtful design to deliver an exceptional mowing experience. Its impressive features, including a strong engine, hydrostatic transmission, ergonomic controls, and advanced mowing technology, make it an ideal choice for homeowners looking for performance and reliability in their lawn care equipment. Whether you are maintaining a small yard or a larger landscape, the YTH2242T stands out as a dependable partner for all your mowing needs.
Top Page Image Contents