Husqvarna CTH2036 Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 23

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

Depress clutch/brake pedal fully and set parking brake.

Place motion control lever in neutral (N) position.

Place attachment clutch in “DISENGAGED” position.

Turn ignition key to “STOP” and remove key.

Make sure the blades and all moving parts have completely stopped.

Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 25)

Mower will be easier to remove from the right side of trac- tor.

Place attachment clutch control in “DISENGAGED” position.

Move attachment lift lever forward to lower mower to its lowest position.

Roll belt off clutch pulley.

Disconnect anti-sway bar from chassis bracket by removing retainer spring.

Disconnect suspension arms from rear deck brackets by removing retainer springs.

Disconnect front links from deck by removing retainer springs.

Raise lift lever to raise suspension arms. Slide mower out from under tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINKS.

TO INSTALL MOWER (See Fig. 25)

Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control. Engage park- ing brake.

Slide mower under tractor.

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

Install belt into clutch pulley groove.

Install left front link into the left hand front mower bracket (retain with single loop retainer springs as shown).

Slide right side of mower back and install right front link into right hand front mower bracket (retain with single loop retainer springs).

Place the suspension arms on mower pins, if necessary, rock and raise front of mower to align mower pins with the holes in suspension arms. Retain with double loop retainer spring, loop down as shown.

Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

Raise deck to highest position.

RETAINER

 

SPRING

CLUTCH PULLEY

SUSPENTION

ARMS

 

 

FRONT LINKS

RETAINER SPRING

RETAINER SPRINGS

ANTI SWAY

BAR

FIG. 25

23

Image 23
Contents CTH2036 Twin II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceIII. Children Table of Contents Unassembled Parts Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CAR- TONTractor See Figs A-4D Install Seat See FigTo Install Bagger Components to To Assemble Bagger See Figs A-5C Bagger Adjustment SeeTo Assemble and Install Mulcher Plug See Fig Horizontal AdjustmentVertical Adjustment Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigUsing the Reverse Operation System See Fig To Operate Mower See FigTo Transport See Figs Service REMINDER/HOUR MeterTo Operate on Hills To Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMulching Mowing Tips Mowing TipsTo Convert Mower See To Dump Bagger SeeBagging See Lubrication Chart MaintenanceCheck Operator Presence System TractorBlade CARESee Figs.20-22 Star Pattern BladeEngine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment To Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Carburetor To Start Engine with a Weak BAT- TeryEngine OIL StorageOther Fuel SystemTroubleshooting Points With attachment clutch TRACTOR- -MODEL NO. CTH2036TWIN 96061021700, Product no 61 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly 532 19 Steering Wheel Engine 532 18 Control Throttle 532 18 Seat Seat AssemblyWheels & Tires DecalsMower CRD Mower Lift 532 16 52-49 Tube Handle Bagger CRD BaggerService Notes Service Notes Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation532 41 02-43 Rev 02.06.07 TB

CTH2036 specifications

The Husqvarna CTH2036 is a robust and versatile ride-on mower designed for homeowners with medium to large lawns. It combines power, efficiency, and advanced technology to make your mowing experience pleasant and effective.

One of the standout features of the CTH2036 is its powerful engine. The mower is equipped with a reliable 19.5 HP Briggs & Stratton V-Twin engine, providing ample power to tackle various terrains. This engine is designed for smooth operation and excellent reliability, ensuring that users can maintain their lawns with minimal hassle.

The cutting deck of the CTH2036 is another highlight. It features a 36-inch cutting width, which allows for efficient mowing in larger spaces without the need for multiple passes. The deck is designed with a reinforced structure that enhances durability, ensuring it stands up to the rigors of frequent use. Additionally, the deck height can be easily adjusted, allowing users to customize their cut to suit different grass types and conditions, ranging from 1 to 4 inches.

User comfort is a critical aspect of the Husqvarna CTH2036. The mower boasts an ergonomic seat with an adjustable backrest, providing excellent support during longer mowing sessions. The steering wheel is designed for easy maneuverability, making it simple to navigate around flower beds, trees, and other obstacles.

Another innovative feature is the integrated mowing technology. The CTH2036 employs an efficient bagging system that collects clippings effectively, reducing the need for additional cleanup after mowing. The mower also supports side discharge for users who prefer that option, offering flexibility in lawn care preferences.

In terms of ease of use, the CTH2036 is equipped with a simple and intuitive control panel that allows users to operate all mowing functions easily. Moreover, it features a hydrostatic transmission, providing smooth acceleration and deceleration without the need for shifting gears.

Durability is a hallmark of the Husqvarna brand, and the CTH2036 is no exception. Built to withstand harsh weather conditions and regular wear, the mower features a solid chassis and high-quality components, ensuring long-lasting performance.

In summary, the Husqvarna CTH2036 is an impressive ride-on mower that combines power, reliability, and ease of use. Its powerful engine, efficient cutting deck, user-friendly design, and innovative technologies make it an ideal choice for homeowners looking to maintain their lawns with excellence and ease. Whether it’s for regular mowing or tackling challenging terrains, the CTH2036 ensures a satisfying lawn care experience.