Husqvarna CTH2036 owner manual To Assemble Bagger See Figs A-5C, Bagger Adjustment See

Page 8

ASSEMBLY

Using the nuts and flat washers removed from tractor back plate, install the bagger support tube to the back plate as shown. Tighten securely.

SUPPORT TUBE

FLAT WASHER

3/8 NUT

BOLT

02330

 

FIG. 4B

Install the two upper support brackets through the back plate and to the chassis, install the clevis pin 10x17mm and secure with retainer spring.

Assemble both support brackets to the outside of the bagger support tube using two each 3/8 x 63,5mm hex bolts13/32" I.D. flat washers and 3/8 locknuts from parts bag. Tighten securely.

Replace discharge chute into rear opening of tractor. Secure the chute with the two hook straps.

CLEVIS PIN 10 X 17MM

3/8 LOCK NUT

SUPPORT BRACKET

10,3MM (13/32")

FLAT WASHER

3/8 X 63,5MM HEX BOLT

RETAINER SPRING

90

 

0

 

25

FIG. 4C

NOTE: The strap hook must go through the discharge chute only. Do not allow the hook to enter the slot in the tractor back plate. This will allow the discharge chute to float with the mower deck when moving on uneven terrain.

DISCHARGE

CHUTE

HOOK

02

306

BACKPLATE

SLOT

FIG. 4D

8

TO ASSEMBLE BAGGER (See Figs. 5A-5C)

Unfold bag by pivoting front bagger tube all the way forward and pressing the bottom vinyl binding onto the tube.

Inside the bag, install spreader bars and retainer springs onto pins on both sides of bag as shown.

Press the vinyl bindings onto the sides of front bagger tube.

Slide the bagger dump handle through the hole in the bagger top, install the clevis pin 10 x 44mm and secure with retainer spring.

FRONT BAGGER TUBE

5

 

90

 

02

VINYL BINDING

 

FIG. 5A

SPREADER BARS

RETAINER

SPRING

VINYL

BINDING

RETAINER SPRING

02906

FIG. 5B

Push cap over end of bagger dump handle.

NOTE: For future use, the clevis pin may be removed in order to use the handle to clear the chute in the event it has become clogged.

DUMP HANDLE

TUBE

CLEVIS PIN 10 X 44MM

RETAINER SPRING

 

07

CAP

029

 

FIG. 5C

BAGGER ADJUSTMENT (See Fig. 6 & 7)

For proper bag function and appearance, it may be nec- essary to adjust the bagger assembly. There should be 6mm (1/4")-9mm (3/8") gap between the bagger top and fender and the bagger top surface should be even with the top surface of the fender. To adjust bagger position:

Image 8
Contents CTH2036 Twin Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Unassembled Parts Assembly Tools Required for AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidTractor See Figs A-4D Install Seat See FigTo Install Bagger Components to Bagger Adjustment See To Assemble Bagger See Figs A-5CTo Assemble and Install Mulcher Plug See Fig Horizontal AdjustmentVertical Adjustment Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig Using the Reverse Operation System See FigTo Operate Mower See Fig Reverse Operation System ROSTo Transport See Figs Service REMINDER/HOUR MeterTo Operate on Hills Before Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsTo Convert Mower See To Dump Bagger SeeBagging See Maintenance Lubrication ChartTractor Blade CARESee Figs.20-22Star Pattern Blade Check Operator Presence SystemEngine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake Belt RemovalFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment To Adjust Throttle Control Cable To Adjust CarburetorTo Start Engine with a Weak BAT- Tery To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points With attachment clutch Schematic TRACTOR- -MODEL NO. CTH2036TWIN 96061021700, Product no 61Electrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly 532 19 Steering Wheel Engine 532 18 Control Throttle Seat Assembly 532 18 SeatDecals Wheels & TiresMower CRD Mower Lift Bagger 532 16 52-49 Tube Handle Bagger CRDService Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX532 41 02-43 Rev 02.06.07 TB

CTH2036 specifications

The Husqvarna CTH2036 is a robust and versatile ride-on mower designed for homeowners with medium to large lawns. It combines power, efficiency, and advanced technology to make your mowing experience pleasant and effective.

One of the standout features of the CTH2036 is its powerful engine. The mower is equipped with a reliable 19.5 HP Briggs & Stratton V-Twin engine, providing ample power to tackle various terrains. This engine is designed for smooth operation and excellent reliability, ensuring that users can maintain their lawns with minimal hassle.

The cutting deck of the CTH2036 is another highlight. It features a 36-inch cutting width, which allows for efficient mowing in larger spaces without the need for multiple passes. The deck is designed with a reinforced structure that enhances durability, ensuring it stands up to the rigors of frequent use. Additionally, the deck height can be easily adjusted, allowing users to customize their cut to suit different grass types and conditions, ranging from 1 to 4 inches.

User comfort is a critical aspect of the Husqvarna CTH2036. The mower boasts an ergonomic seat with an adjustable backrest, providing excellent support during longer mowing sessions. The steering wheel is designed for easy maneuverability, making it simple to navigate around flower beds, trees, and other obstacles.

Another innovative feature is the integrated mowing technology. The CTH2036 employs an efficient bagging system that collects clippings effectively, reducing the need for additional cleanup after mowing. The mower also supports side discharge for users who prefer that option, offering flexibility in lawn care preferences.

In terms of ease of use, the CTH2036 is equipped with a simple and intuitive control panel that allows users to operate all mowing functions easily. Moreover, it features a hydrostatic transmission, providing smooth acceleration and deceleration without the need for shifting gears.

Durability is a hallmark of the Husqvarna brand, and the CTH2036 is no exception. Built to withstand harsh weather conditions and regular wear, the mower features a solid chassis and high-quality components, ensuring long-lasting performance.

In summary, the Husqvarna CTH2036 is an impressive ride-on mower that combines power, reliability, and ease of use. Its powerful engine, efficient cutting deck, user-friendly design, and innovative technologies make it an ideal choice for homeowners looking to maintain their lawns with excellence and ease. Whether it’s for regular mowing or tackling challenging terrains, the CTH2036 ensures a satisfying lawn care experience.