Husqvarna CTH2036 owner manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 24

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 26 and 27)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE OF

 

BOTTOM EDGE

MOWER

00598

OF MOWER

 

 

TO GROUND

 

TO GROUND

“A”

GROUND LINE

“A”

FIG. 26

SUSPENSION ARM

01553

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

01268

MANDREL

"D"

"D"

FIG. 28

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

01267

LIFT LINK ADJUSTMENT NUT

FIG. 27

FRONT-TO-BACK ADJUSTMENT (See Figs. 28 and 29)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

FIG. 29

NUT "E"

NUT "F"

TRUNNION

FRONT LINKS

FIG. 30

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents CTH2036 Twin Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts Assembly Tools Required for AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidInstall Seat See Fig To Install Bagger Components toTractor See Figs A-4D Bagger Adjustment See To Assemble Bagger See Figs A-5CHorizontal Adjustment Vertical AdjustmentTo Assemble and Install Mulcher Plug See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig Using the Reverse Operation System See FigTo Operate Mower See Fig Reverse Operation System ROSService REMINDER/HOUR Meter To Operate on HillsTo Transport See Figs Before Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsTo Dump Bagger See Bagging SeeTo Convert Mower See Maintenance Lubrication ChartTractor Blade CARESee Figs.20-22Star Pattern Blade Check Operator Presence SystemEngine Cleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake Belt RemovalTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER To Adjust Throttle Control Cable To Adjust CarburetorTo Start Engine with a Weak BAT- Tery To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points With attachment clutch Schematic TRACTOR- -MODEL NO. CTH2036TWIN 96061021700, Product no 61Electrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly 532 19 Steering Wheel Engine 532 18 Control Throttle Seat Assembly 532 18 SeatDecals Wheels & TiresMower CRD Mower Lift Bagger 532 16 52-49 Tube Handle Bagger CRDService Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX532 41 02-43 Rev 02.06.07 TB

CTH2036 specifications

The Husqvarna CTH2036 is a robust and versatile ride-on mower designed for homeowners with medium to large lawns. It combines power, efficiency, and advanced technology to make your mowing experience pleasant and effective.

One of the standout features of the CTH2036 is its powerful engine. The mower is equipped with a reliable 19.5 HP Briggs & Stratton V-Twin engine, providing ample power to tackle various terrains. This engine is designed for smooth operation and excellent reliability, ensuring that users can maintain their lawns with minimal hassle.

The cutting deck of the CTH2036 is another highlight. It features a 36-inch cutting width, which allows for efficient mowing in larger spaces without the need for multiple passes. The deck is designed with a reinforced structure that enhances durability, ensuring it stands up to the rigors of frequent use. Additionally, the deck height can be easily adjusted, allowing users to customize their cut to suit different grass types and conditions, ranging from 1 to 4 inches.

User comfort is a critical aspect of the Husqvarna CTH2036. The mower boasts an ergonomic seat with an adjustable backrest, providing excellent support during longer mowing sessions. The steering wheel is designed for easy maneuverability, making it simple to navigate around flower beds, trees, and other obstacles.

Another innovative feature is the integrated mowing technology. The CTH2036 employs an efficient bagging system that collects clippings effectively, reducing the need for additional cleanup after mowing. The mower also supports side discharge for users who prefer that option, offering flexibility in lawn care preferences.

In terms of ease of use, the CTH2036 is equipped with a simple and intuitive control panel that allows users to operate all mowing functions easily. Moreover, it features a hydrostatic transmission, providing smooth acceleration and deceleration without the need for shifting gears.

Durability is a hallmark of the Husqvarna brand, and the CTH2036 is no exception. Built to withstand harsh weather conditions and regular wear, the mower features a solid chassis and high-quality components, ensuring long-lasting performance.

In summary, the Husqvarna CTH2036 is an impressive ride-on mower that combines power, reliability, and ease of use. Its powerful engine, efficient cutting deck, user-friendly design, and innovative technologies make it an ideal choice for homeowners looking to maintain their lawns with excellence and ease. Whether it’s for regular mowing or tackling challenging terrains, the CTH2036 ensures a satisfying lawn care experience.
Top Page Image Contents