Husqvarna CTH2036 owner manual To Start Engine with a Weak BAT- Tery, To Replace Headlight Bulb

Page 27

SERVICE AND ADJUSTMENTS

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR WHEEL ONLY)

FIG. 34

TO START ENGINE WITH A WEAK BAT- TERY

(See Fig. 35)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

 

02614

WEAK OR DEAD

FULLY CHARGED

BATTERY

BATTERY

FIG. 35

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 36)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT WIRE

CONNECTOR

02778

FIG. 36

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engine manual.

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need

27adjustment, see engine manual.

Page 26 Page 28
Image 27
Page 26 Page 28
Contents CTH2036 Twin II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CAR- TONInstall Seat See Fig To Install Bagger Components toTractor See Figs A-4D To Assemble Bagger See Figs A-5C Bagger Adjustment SeeHorizontal Adjustment Vertical AdjustmentTo Assemble and Install Mulcher Plug See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigUsing the Reverse Operation System See Fig To Operate Mower See FigService REMINDER/HOUR Meter To Operate on HillsTo Transport See Figs To Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMulching Mowing Tips Mowing TipsTo Dump Bagger See Bagging SeeTo Convert Mower See Lubrication Chart MaintenanceCheck Operator Presence System TractorBlade CARESee Figs.20-22 Star Pattern BladeEngine Cleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER To Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Carburetor To Start Engine with a Weak BAT- TeryEngine OIL StorageOther Fuel SystemTroubleshooting Points With attachment clutch TRACTOR- -MODEL NO. CTH2036TWIN 96061021700, Product no 61 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly 532 19 Steering Wheel Engine 532 18 Control Throttle 532 18 Seat Seat AssemblyWheels & Tires DecalsMower CRD Mower Lift 532 16 52-49 Tube Handle Bagger CRD BaggerService Notes Service Notes Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation532 41 02-43 Rev 02.06.07 TB

CTH2036 specifications

The Husqvarna CTH2036 is a robust and versatile ride-on mower designed for homeowners with medium to large lawns. It combines power, efficiency, and advanced technology to make your mowing experience pleasant and effective.

One of the standout features of the CTH2036 is its powerful engine. The mower is equipped with a reliable 19.5 HP Briggs & Stratton V-Twin engine, providing ample power to tackle various terrains. This engine is designed for smooth operation and excellent reliability, ensuring that users can maintain their lawns with minimal hassle.

The cutting deck of the CTH2036 is another highlight. It features a 36-inch cutting width, which allows for efficient mowing in larger spaces without the need for multiple passes. The deck is designed with a reinforced structure that enhances durability, ensuring it stands up to the rigors of frequent use. Additionally, the deck height can be easily adjusted, allowing users to customize their cut to suit different grass types and conditions, ranging from 1 to 4 inches.

User comfort is a critical aspect of the Husqvarna CTH2036. The mower boasts an ergonomic seat with an adjustable backrest, providing excellent support during longer mowing sessions. The steering wheel is designed for easy maneuverability, making it simple to navigate around flower beds, trees, and other obstacles.

Another innovative feature is the integrated mowing technology. The CTH2036 employs an efficient bagging system that collects clippings effectively, reducing the need for additional cleanup after mowing. The mower also supports side discharge for users who prefer that option, offering flexibility in lawn care preferences.

In terms of ease of use, the CTH2036 is equipped with a simple and intuitive control panel that allows users to operate all mowing functions easily. Moreover, it features a hydrostatic transmission, providing smooth acceleration and deceleration without the need for shifting gears.

Durability is a hallmark of the Husqvarna brand, and the CTH2036 is no exception. Built to withstand harsh weather conditions and regular wear, the mower features a solid chassis and high-quality components, ensuring long-lasting performance.

In summary, the Husqvarna CTH2036 is an impressive ride-on mower that combines power, reliability, and ease of use. Its powerful engine, efficient cutting deck, user-friendly design, and innovative technologies make it an ideal choice for homeowners looking to maintain their lawns with excellence and ease. Whether it’s for regular mowing or tackling challenging terrains, the CTH2036 ensures a satisfying lawn care experience.
Top Page Image Contents