Husqvarna CTH2036T Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 21

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

•Depress brake pedal fully and set parking brake.

•Place motion control lever in neutral position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 28)

Mower will be easier to remove from the right side of trac- tor.

•Place attachment clutch control in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off clutch pulley.

•Disconnect anti-sway bar from chassis bracket by removing retainer spring.

•Disconnect suspension arms from rear deck brackets by removing retainer springs.

•Disconnect front links from deck by removing retainer springs.

•Raise lift lever to raise suspension arms. Slide mower out from under tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINKS.

TO INSTALL MOWER (See Fig. 28)

Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control. Engage park- ing brake.

•Slide mower under tractor.

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

•Install belt into clutch pulley groove.

•Install left front link into the left hand front mower bracket (retain with single loop retainer springs as shown).

•Slide right side of mower back and install right front link into right hand front mower bracket (retain with single loop retainer springs).

•Place the suspension arms on mower pins, if neces- sary, rock and raise front of mower to align mower pins with the holes in suspension arms. Retain with double loop retainer spring, loop down as shown.

•Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

•Raise deck to highest position.

RETAINER

 

SPRING

CLUTCH PULLEY

SUSPENTION

ARMS

 

 

FRONT LINKS

RETAINER SPRING

RETAINER SPRINGS

ANTI SWAY

BAR

Fig. 28

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents CTH2036T Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidTo Install Bagger Components to Tractor See Figs Bagger Adjustment See Fig Horizontal AdjustmentTo Assemble Bagger See Figs Check Tire Pressure Vertical AdjustmentCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Using the Reverse Operation System See Fig To Adjust Gauge Wheels See FigTo Operate Mower See Fig Reverse Operation System ROSBefore Starting the Engine Service REMINDER/HOUR MeterCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP To Dump Bagger See Fig To Convert Mower See FigBagging See Fig Lubrication Chart MaintenanceBlade Care See Fig TractorStar Pattern Blade See Fig Check Operator Presence SystemEngine Cleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig To Replace Mower Blade Drive Belt To Level Mower HousingSee Fig Belt RemovalBelt Installation Transaxle Motion Control Lever Neutral Adjustment See FigTo Check Brake To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment To Adjust Motion Control Lever See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Other StorageFuel System Engine OILTroubleshooting Points Engine continues Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationService Notes Service Notes 532 42 66-43 04.01.09 CL
Top Page Image Contents