Husqvarna CTH2036T To Assemble Bagger See Figs, Bagger Adjustment See Fig, Horizontal Adjustment

Page 8

ASSEMBLY

CLEVIS PIN 3/8 X 11/16

CLEVIS PIN 3/8 X 2

SUPPORT BRACKET

13/32 FLAT WASHER RETAINER SPRING SUPPORT BRACKET

02813

Fig. 6

DISCHARGE

CHUTE

HOOK

02306

BACKPLATE

SLOT

Fig. 7

TO ASSEMBLE BAGGER (See Figs. 8-10)

•Unfold bag by pivoting front bagger tube all the way forward and pressing the bottom vinyl binding onto the tube.

5 0290 FRONT BAGGER TUBE

VINYL

BINDING

Fig. 8

•Inside the bag, install spreader bars and retainer springs onto pins on both sides of bag as shown.

•Press the vinyl bindings onto the sides of front bagger tube.

SPREADER BARS

(Inside of bag)

RETAINER SPRING

VINYL BINDING

 

02906

RETAINER

VINYL

SPRING

BINDING

 

Fig. 9

•Slide the bagger dump handle through the hole in the bagger top, install the clevis pin 10 x 44mm and secure with retainer clip.

•Push cap over end of bagger dump handle.

NOTE: For future use, the clevis pin may be removed in order to use the handle to clear the chute in the event it has become clogged.

DUMP HANDLE

TUBE

CLEVIS PIN

3/8 X 1-3/4

RETAINER

CLIP

CAP

02907

Fig. 10

BAGGER ADJUSTMENT (See Fig. 11)

For proper bag function and appearance, it may be neces- sary to adjust the bagger assembly. There should be 6mm (1/4")-9mm (3/8") gap between the bagger top and fender and the bagger top surface should be even with the top surface of the fender. To adjust bagger position:

HORIZONTAL ADJUSTMENT

•Slightly loosen the nuts securing the bagger RH and LH horizontal adjustment brackets. Loosen only enough so the brackets keep their position, but allow them to be moved.

•Move the brackets the amount forward or backward you wish the bag assembly to move. Retighten the

8nuts securely.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents CTH2036T Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Unassembled Parts Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidTo Install Bagger Components to Tractor See Figs To Assemble Bagger See Figs Bagger Adjustment See FigHorizontal Adjustment Vertical Adjustment Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig Using the Reverse Operation System See FigTo Operate Mower See Fig Reverse Operation System ROSService REMINDER/HOUR Meter Before Starting the EngineCheck Engine OIL Level ADD GasolineAutomatic Transmission Warm UP Mowing TipsPurge Transmission Bagging See Fig To Dump Bagger See FigTo Convert Mower See Fig Maintenance Lubrication ChartTractor Blade Care See FigStar Pattern Blade See Fig Check Operator Presence SystemEngine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing To Replace Mower Blade Drive BeltSee Fig Belt RemovalTransaxle Motion Control Lever Neutral Adjustment See Fig Belt InstallationTo Check Brake To Replace Motion Drive Belt See FigTo Adjust Motion Control Lever See Fig To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Storage OtherFuel System Engine OILTroubleshooting Points Engine continues Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXService Notes Service Notes 532 42 66-43 04.01.09 CL
Top Page Image Contents