Husqvarna 288XP, 288XP Lite, 281XP, 288XP Clearing the trunk and preparing your retreat, Felling

Page 22

SAFETY INSTRUCTIONS

C Clearing the trunk and preparing your retreat

Remove any branches that are in the way. To do this it is best to work from the top down and keep the trunk between you and the chain saw. Never limb above shoulder height.

Remove any undergrowth from the base of the tree and check the area for obstacles (stones, branches, holes, etc.) so that you have a clear path of retreat when the tree starts to fall. Your path of retreat should be roughly 135 degrees behind the intended felling direction.

D Felling

Felling is done using three cuts. First you make the DIRECTIONAL CUTS, which consist of the TOP CUT and the BOTTOM CUT; followed by the FELLING CUT. By placing these cuts correctly you can control the felling direction very accurately.

DIRECTIONAL CUT

To make the DIRECTIONAL CUT you begin with the TOP CUT. Stand to the right of the tree and cut downwards at an angle.

Next make the BOTTOM CUT so that it finishes at the end of the TOP CUT.

The directional cut should run 1/4 of the diameter through the trunk and the angle between the TOP CUT and BOTTOM CUT should be 45°.

The line where the two cuts meet is called the

DIRECTIONAL CUT LINE. This line should be perfectly horizontal and at right angles (90°) to the chosen felling direction.

FELLING CUT

The felling cut is made from the opposite side of the tree and it must be perfectly horizontal. Stand on the left side of the tree and cut with the bottom edge of the bar.

Make the FELLING CUT about 3-5 cm (1.5-2 inches) above the flat section of the

DIRECTIONAL CUT.

Use full throttle and bring the bar and chain slowly into the tree. Make sure the tree does not start to move in the opposite direction to your intended felling direction. Drive a WEDGE or BREA- KING BAR into the cut as soon as it is deep enough.

Finish the FELLING CUT parallel with the DIRECTIONAL CUT LINE so that the distance between them is at least at least 1/10 of the trunk diameter. The uncut section of the trunk is called the BREAKING STRIP.

The BREAKING STRIP act as hinges that control the felling direction of the falling tree.

All control over the felling direction is lost if the BREA- KING STRIP is too narrow or if the directional cut and felling cut are badly placed.

When the felling cut and directional cut are complete the tree should start to fall under its own weight or with the aid of a FELLING WEDGE or BREAKING BAR.

22 – English

Page 21 Page 23
Image 22
Page 21 Page 23
Contents 288XP/XP Lite 101 90KEY to Symbols SymbolsContents Chain SAW Safety Equipment Safety InstructionsPersonal Protective Equipment Chain brake and front hand guard Chain catcher Throttle lockRight hand guard Vibration damping system Stop switchMuffler Checking the automatic brake Checking brake band wearChecking the front hand guard Checking the brake triggerThrottle lock Cutting Equipment 5 basic rulesSaw chain Cutting equipment designed to minimise kickbackBar Some terms that describe the bar and chainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting raker clearanceSharpening cutting teeth Setting the raker clearance General advice on setting raker clearanceTensioning the chain Filling with chain oil Lubricating cutting equipmentChain oil Never use waste oilChecking wear on cutting equipment Checking chain lubricationLubricating the clutch drum bearing Lubricating the bar tip sprocketHOW to Avoid Kickback What is kickback?Do not let go of the handles General rulesNever use the saw one- handed Min m General Safety Precautions10 ft Basic safety rules General Working InstructionsTerms Basic cutting techniqueGeneral CuttingLimbing Tree felling techniqueSafe distance Felling directionClearing the trunk and preparing your retreat FellingCutting the trunk into logs General adviceFreeing a tree that has fallen badly = high accident risk Freeing a Trapped treeWhat is WHAT? Assembly Mounting guide bar and chainFuel Handling FuelmixMin 3 m Fuelling10ft Cold engine Start and StopStart Warm engineMaintenance CarburetorChanging a broken or worn starter cord Starter device assemblyStarter device Tensioning the recoil springSpark plug Adjusting the oil pumpAir filter MufflerTemperature -5oC 23oF or colder Needle bearing maintenance Winter useTemperature 0oC 32oF or colder Cooling systemWeekly maintenance Daily maintenance Monthly maintenanceTechnical Data Federal Emission Control Warranty Statement Your Warranty Rights Obligations1998W48

281XP, 288XP, 288XP, 288XP Lite specifications

The Husqvarna 288XP is a legendary chainsaw, renowned for its power and performance in the realm of forestry and woodcutting. This heavy-duty saw was designed for professional use, particularly suited for logging and milling tasks. One of its standout features is its high-output 88cc engine, which delivers robust power and exceptional torque. This makes the 288XP ideal for handling large trees and tough cutting jobs, ensuring efficiency and effectiveness in demanding situations.

The chainsaw is equipped with advanced technologies that enhance its performance. Among these technologies is the Air Injection system, which uses centrifugal force to remove large particles before they reach the air filter, promoting better engine efficiency and reducing maintenance needs. Additionally, the 288XP has a state-of-the-art ignition system that ensures easy starting, reducing downtime on the job.

Another noteworthy variant, the 288XP Lite, retains the same powerful engine but is designed with a lighter construction in mind. This makes the saw easier to handle and less fatiguing for extended use, catering especially to professionals who require mobility without sacrificing power.

The Husqvarna 281XP, often considered a sibling to the 288XP, offers slightly less displacement but is equally potent. With its 72cc engine, the 281XP is ideal for a variety of cutting tasks, from felling trees to limbing. It combines an efficient air filtration system with a lightweight design, providing versatility and ease of use for a range of users, from amateurs to seasoned professionals.

All models in the XP series showcase excellent ergonomics, including padded handles and an anti-vibration system, which significantly reduces operator fatigue and increases comfort during prolonged use. The chainsaw's build quality is robust, featuring high-grade materials that withstand the rigors of intensive work environments.

In summary, the Husqvarna 288XP, 288XP Lite, and 281XP are exemplary tools within the professional chainsaw segment. Each model brings unique features and benefits, yet they all share a commitment to power, efficiency, and user comfort. Whether you opt for the powerhouse 288XP or the more maneuverable 281XP, each chainsaw is engineered to deliver superior performance to meet the demands of the toughest jobs.
Top Page Image Contents