Husqvarna 288XP, 288XP Lite, 281XP, 288XP manual Fuel Handling, Fuelmix

Page 26

FUEL HANDLING

Fuelmix

IMPORTANT! The chain saw is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

!Always provide for good ventilation when handling fuel.

Gasoline

•This engine is certified to operate on unleaded gasoline.

•Use good quality unleaded

gasoline.

• The lowest recommended octane rating is 87. If you run the engine on lower octane rating than 87 so- called “knocking“ can occur. This leads to an increased engine temperature, which can result in a serious engine breakdown.

•When working at continuous high revs a higher octane rating is recommended.

Two-stroke oil

•For the best results use HUSQVARNA two-stroke oil, which is especially developed for chain saws. Mixing ratio 1:50 (2%).

•Never use two-stroke oil intended for water cooled outboard engines, so-called, outboard oil.

•Never use oil intended for four-stroke engines.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Gasoline

Oil

 

 

 

 

 

 

 

 

 

2%(1:50)

 

 

 

 

 

 

 

 

 

 

Lit.

Lit.

 

 

 

 

 

 

 

 

 

 

 

 

5

 

0,10

 

 

10

 

0,20

 

 

15

 

0,30

 

 

20

 

0,40

 

 

 

 

US

US

 

 

 

gallon

fl. oz.

 

 

1

 

2 1/2

 

 

2 1/2

 

6 1/2

 

 

5

 

12 7/8

 

 

 

 

 

 

 

 

 

 

 

Mixing

•Always mix the gasoline and oil in a clean container intended for fuel.

•Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline.

•Mix (shake) the fuel mixture thoroughly before filling the saw’s fuel tank.

•Do not mix more than max. one month’s supply of fuel.

•If the saw is not used for some time the fuel tank should be emptied and cleaned.

•This engine is certified to operate on unleaded gasoline.

Chain oil

•The chain lubrication system is automatic. Always use special chain oil with good adhesive characteristics.

•In countries where no special chain oil is available, EP 90 transmission oil can be used.

•Never use waste oil. This results in damage to the oil pump, the bar and the chain.

•It is important to use oil of the right viscosity according to the air temperature.

•In temperatures below 0oC (32oF) some oils become too viscous. This can overload the oil pump and result in damage to the oil pump components.

•Contact your servicing dealer when choosing chain oil.

26 – English

Page 25 Page 27
Image 26
Page 25 Page 27
Contents 288XP/XP Lite 101 90KEY to Symbols SymbolsContents Personal Protective Equipment Safety InstructionsChain SAW Safety Equipment Chain brake and front hand guard Right hand guard Throttle lockChain catcher Muffler Stop switchVibration damping system Checking the automatic brake Checking brake band wearChecking the front hand guard Checking the brake triggerThrottle lock Cutting Equipment 5 basic rulesSaw chain Cutting equipment designed to minimise kickbackBar Some terms that describe the bar and chainSharpening cutting teeth Sharpening your chain and adjusting raker clearanceGeneral information on sharpening cutting teeth Tensioning the chain General advice on setting raker clearanceSetting the raker clearance Filling with chain oil Lubricating cutting equipmentChain oil Never use waste oilChecking wear on cutting equipment Checking chain lubricationLubricating the clutch drum bearing Lubricating the bar tip sprocketHOW to Avoid Kickback What is kickback?Never use the saw one- handed General rulesDo not let go of the handles 10 ft General Safety PrecautionsMin m Basic safety rules General Working InstructionsTerms Basic cutting techniqueGeneral CuttingLimbing Tree felling techniqueSafe distance Felling directionClearing the trunk and preparing your retreat FellingCutting the trunk into logs General adviceFreeing a tree that has fallen badly = high accident risk Freeing a Trapped treeWhat is WHAT? Assembly Mounting guide bar and chainFuel Handling Fuelmix10ft FuellingMin 3 m Cold engine Start and StopStart Warm engineMaintenance CarburetorChanging a broken or worn starter cord Starter device assemblyStarter device Tensioning the recoil springSpark plug Adjusting the oil pumpAir filter MufflerTemperature -5oC 23oF or colder Needle bearing maintenance Winter useTemperature 0oC 32oF or colder Cooling systemWeekly maintenance Daily maintenance Monthly maintenanceTechnical Data Federal Emission Control Warranty Statement Your Warranty Rights Obligations1998W48

281XP, 288XP, 288XP, 288XP Lite specifications

The Husqvarna 288XP is a legendary chainsaw, renowned for its power and performance in the realm of forestry and woodcutting. This heavy-duty saw was designed for professional use, particularly suited for logging and milling tasks. One of its standout features is its high-output 88cc engine, which delivers robust power and exceptional torque. This makes the 288XP ideal for handling large trees and tough cutting jobs, ensuring efficiency and effectiveness in demanding situations.

The chainsaw is equipped with advanced technologies that enhance its performance. Among these technologies is the Air Injection system, which uses centrifugal force to remove large particles before they reach the air filter, promoting better engine efficiency and reducing maintenance needs. Additionally, the 288XP has a state-of-the-art ignition system that ensures easy starting, reducing downtime on the job.

Another noteworthy variant, the 288XP Lite, retains the same powerful engine but is designed with a lighter construction in mind. This makes the saw easier to handle and less fatiguing for extended use, catering especially to professionals who require mobility without sacrificing power.

The Husqvarna 281XP, often considered a sibling to the 288XP, offers slightly less displacement but is equally potent. With its 72cc engine, the 281XP is ideal for a variety of cutting tasks, from felling trees to limbing. It combines an efficient air filtration system with a lightweight design, providing versatility and ease of use for a range of users, from amateurs to seasoned professionals.

All models in the XP series showcase excellent ergonomics, including padded handles and an anti-vibration system, which significantly reduces operator fatigue and increases comfort during prolonged use. The chainsaw's build quality is robust, featuring high-grade materials that withstand the rigors of intensive work environments.

In summary, the Husqvarna 288XP, 288XP Lite, and 281XP are exemplary tools within the professional chainsaw segment. Each model brings unique features and benefits, yet they all share a commitment to power, efficiency, and user comfort. Whether you opt for the powerhouse 288XP or the more maneuverable 281XP, each chainsaw is engineered to deliver superior performance to meet the demands of the toughest jobs.
Top Page Image Contents