Husqvarna T435 KEY to Symbols, Symbols on the machine, Symbols in the operator’s manual

Page 2

KEY TO SYMBOLS

Symbols on the machine:

WARNING! Chain saws can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others.

Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.

Always wear:

• Approved protective helmet

• Approved hearing protection

•Protective goggles or a visor

This product is in accordance with applicable EC directives.

Noise emission to the environment according to the European Community’s Directive. The machine’s emission is speciﬁed in chapter Technical data and on label.

Both of the operator′s hands must be used to operate the chain saw.

Never operate a chain saw holding it with one hand only.

Never let the guide bar tip come in contact with any object.

Use appropriate protections for foot-leg and hand-arm.

Never let the guide bar tip come in contact with any object.

WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, and cause a lightning fast reverse reaction, kicking the guide bar up and towards the operator. May cause serious personal injury.

This saw should only be used by persons who are specially trained in tree maintenance work. See operator’s manual!

2 – English

Working position

Choke

Other symbols/decals on the machine refer to special certiﬁcation requirements for certain markets.

Symbols in the operator’s manual:

Switch off the engine before carrying out any checks or maintenance.

Always wear approved protective gloves.

Regular cleaning is required.

Visual check.

Protective goggles or a visor must be worn.

Refuelling.

Filling with oil and adjusting oil ﬂow.

The chain brake must be engaged when the chain saw is started.

WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, and cause a lightning fast reverse reaction, kicking the guide bar up and towards the operator. May cause serious personal injury.

Image 2

Contents T435 Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Machine′s safety equipment Personal protective equipmentChain brake and front hand guard Vibration damping system Throttle lockoutChain catcher Mufﬂer Stop switchCutting equipment General rulesBar Sharpening your chain and adjusting depth gauge settingCutting equipment designed to reduce kickback ChainToo large General advice on adjusting depth gauge settingIncreased if the depth gauge setting is Lubricating cutting equipment Adjustment of depth gauge settingTensioning the chain Cause serious or even fatal injuryChain drive sprocket Filling with chain oilChecking chain lubrication Checking wear on cutting equipmentBar Fitting a spike bumper AssemblyFitting the bar and chain Working with the chainFuel Handling FuelTransport and storage Fuel safetyFuelling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsAlways use a fast cutting speed, i.e. full throttle English Preparing to use the saw in the tree Using the chainsaw in the treeGeneral requirements working at height Basic cutting technique Working Techniques Safe distance Felling technique for tree topsLimbing Felling directionCutting trees and branches that are in tension Freeing a tree that has fallen badlyFelling cut General advice How to avoid kickbackWhat is kickback? Cutting the trunk into logsGeneral MaintenanceCarburettor adjustment Correctly adjusted carburettor High speed jet HMufﬂer Starter Changing a broken or worn starter cordFitting the starter Tensioning the recoil springChanging a broken recoil spring Lubricating the bar tip sprocket Air ﬁlterSpark plug Must always be replacedCooling system Adjustment of the oil pumpRunning when making adjustments Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical data Applies to Europe only Bar and chain combinationsSaw chain ﬁling and ﬁle gauges EC-declaration of conformity Cispr 122001, EN ISOPage Page Page ´z+S?h¶6¨ Page 1151317-26