Husqvarna T435 manual Bar and chain combinations, Applies to Europe only, Cispr 122001, EN ISO

Page 38

MAINTENANCE

Bar and chain combinations

The following combinations are CE approved.

		Bar			Chain

Length, inch	Pitch, inch	Gauge, mm	Max. nose radius	Type	Length, drive links (no.)

12	3/8	0,050	7 T		45

14	3/8	0,050	7T	Husqvarna H36	52

16	3/8	0,050	7T		56

Saw chain ﬁling and ﬁle gauges

EC-declaration of conformity

(Applies to Europe only)

Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, declares under sole responsibility that the chain saw Husqvarna T435 from 2009’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), is in conformity with the requirements of the COUNCIL’S DIRECTIVES:

-of June 22, 1998 ”relating to machinery” 98/37/EC, annex IIA.

-of December 15, 2004 ”relating to electromagnetic compatibility” 2004/108/EC.

-of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC.

For information relating to noise emissions, see the chapter Technical data. The following standards have been applied:

CISPR 12:2001, EN ISO 11681-2.

Notiﬁed body: 0404, SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has carried out EC type examination in accordance with the machinery directive’s (98/37/EC) article 8, point 2c. The certiﬁcates for EC type examination in accordance with annex VI, have the numbers: 404/08/1276

In addition, SMP, Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has certiﬁed conformity with annex V of the Council’s Directive of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC. The certiﬁcates have the numbers: 01/161/080

The supplied chain saw conforms to the example that underwent EC type examination.

Huskvarna January 9, 2009

Bengt Frögelius, Development director chainsaw R&D

38 – English

Image 38

Contents T435 Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Machine′s safety equipment Personal protective equipmentChain brake and front hand guard Vibration damping system Throttle lockoutChain catcher Mufﬂer Stop switchCutting equipment General rulesBar Sharpening your chain and adjusting depth gauge settingCutting equipment designed to reduce kickback ChainToo large General advice on adjusting depth gauge settingIncreased if the depth gauge setting is Lubricating cutting equipment Adjustment of depth gauge settingTensioning the chain Cause serious or even fatal injuryChain drive sprocket Filling with chain oilChecking chain lubrication Checking wear on cutting equipmentBar Fitting a spike bumper AssemblyFitting the bar and chain Working with the chainFuel Handling FuelTransport and storage Fuel safetyFuelling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsAlways use a fast cutting speed, i.e. full throttle English Preparing to use the saw in the tree Using the chainsaw in the treeGeneral requirements working at height Basic cutting technique Working Techniques Safe distance Felling technique for tree topsLimbing Felling directionCutting trees and branches that are in tension Freeing a tree that has fallen badlyFelling cut General advice How to avoid kickbackWhat is kickback? Cutting the trunk into logsGeneral MaintenanceCarburettor adjustment Correctly adjusted carburettor High speed jet HMufﬂer Starter Changing a broken or worn starter cordFitting the starter Tensioning the recoil springChanging a broken recoil spring Lubricating the bar tip sprocket Air ﬁlterSpark plug Must always be replacedCooling system Adjustment of the oil pumpRunning when making adjustments Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical data Applies to Europe only Bar and chain combinationsSaw chain ﬁling and ﬁle gauges EC-declaration of conformity Cispr 122001, EN ISOPage Page Page ´z+S?h¶6¨ Page 1151317-26