Husqvarna 455, 465, 460 Air filter, Spark plug, Needle bearing lubrication, Fitting the starter

Page 35

MAINTENANCE

Fitting the starter

To fit the starter, first pull out the starter cord and place the starter in position against the crankcase. Then slowly release the starter cord so that the pulley engages with the pawls.

Fit and tighten the screws that hold the starter.

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

Carburettor malfunctions

Starting problems

Loss of engine power

Unnecessary wear to engine parts.

Excessive fuel consumption.

Remove the air filter after taking off the air filter cover. When refitting make sure that the air filter seals tightly against the filter holder. Clean the filter by brushing or shaking it.

The filter can be cleaned more thoroughly by washing it in water and detergent.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced.

A HUSQVARNA chain saw can be equipped with different types of air filter according to working conditions, weather, season, etc. Contact your dealer for advice.

Spark plug

The spark plug condition is influenced by:

An incorrect fuel mixture (too much or incorrect type of oil).

A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0,5 mm. The spark plug should be replaced after about a month in operation or earlier if necessary.

Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regularly (once a week).

When lubricating, remove the clutch cover by loosening the two bar nuts. Lay the saw on its side with the clutch drum upwards.

Lubrication involves engine oil dripping into the centre of the clutch drum as it rotates.

English 35

Image 35
Contents English Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsChain brake and front hand guard Machine′s safety equipmentAlways use common sense Personal protective equipmentGeneral Safety Precautions Right hand guard Throttle lockoutChain catcher Muffler Stop switchCutting equipment Vibration damping systemCutting equipment designed to reduce kickback General rulesGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain Lubricating cutting equipment Rancher II, 460 Rancher II, 465 Rancher455e Rancher II, 455e Rancher II TrioBrake Needle bearing lubrication Filling with chain oilChecking chain lubrication Chain drive sprocketGuide bar Working with the chain AssemblyFitting the bar and chain Fitting a spike bumper Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageCold engine Starting and StoppingStarting and stopping StartingStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Basic cutting technique Safe distance Tree felling techniqueDirectional cuts Felling directionClearing the trunk and preparing your retreat Felling cut Freeing a tree that has fallen badly How to avoid kickbackWhat is kickback? Cutting the trunk into logs General MaintenanceCarburettor adjustment Checking the inertia brake release Muffler Changing a broken recoil spring StarterChanging a broken or worn starter cord Tensioning the recoil springFitting the starter Air filterSpark plug Needle bearing lubricationCooling system Adjustment of the oil pumpAir Injection centrifugal cleaning Temperature 0C or colderTemperature -5C or colder Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataRancher Engine Saw chain filing and file gauges Guide bar and saw chain combinationsEN ISO 121002010, ISO 149821998, EN ISO EC-declaration of conformityApplies to Europe only Page Original instructions 1154135-26
Related manuals
Manual 44 pages 48.45 Kb

455, 455e, 460, 465 specifications

The Husqvarna 460 and 455 series chainsaws are some of the most popular models in their class, recognized for their reliability, performance, and advanced technology. These machines are designed to meet the demands of both professionals and enthusiasts who require powerful tools for cutting firewood, felling trees, or performing tree maintenance.

The Husqvarna 460 is equipped with a robust 60.3 cc engine that delivers impressive power and efficiency. With a power output of approximately 3.6 kW, this chainsaw is capable of handling ambitious cutting tasks with ease. The design of the 460 includes a low-vibration system that significantly reduces operator fatigue during extended use. This is achieved through effective isolating features that dampen vibrations transferred to the user's hands, allowing for more comfortable operation over longer periods.

One of the standout features of the Husqvarna 460 is its X-Torq engine technology. This innovative design reduces fuel consumption by up to 20% while also decreasing harmful exhaust emissions. This is increasingly important for environmentally conscious users, as it allows for a greener operation without compromising performance. The chainsaw is also equipped with an air injection system that effectively removes larger particles from the air before they reach the filtration system, ensuring cleaner air intake and extending the lifespan of the air filter.

On the other hand, the Husqvarna 455 Rancher is another exceptional model known for its versatility and robust design. Featuring a slightly smaller 55.5 cc engine, it offers a solid power output of around 2.6 kW, making it suitable for a wide range of tasks from cutting firewood to clearing brush. The 455 Rancher shares many of the same technological advancements as the 460, including the X-Torq engine and low-vibration technology, providing users with similar benefits in terms of efficiency and comfort.

Both models feature an adjustable oil pump for better chain lubrication, ensuring smooth operation and prolonging the chain's life. Additionally, the easy access air filter and tool-less chain tensioning allow for quick maintenance and adjustments in the field, making them user-friendly choices.

Overall, the Husqvarna 460 and 455 series chainsaws combine power, efficiency, and advanced technology, catering to the needs of both casual users and professionals alike. Their thoughtful design and robust performance establish them as reliable tools in any cutting task, making them a top choice for those in need of high-quality chainsaws.