Husqvarna 570 576 XP manual Limbing

Page 24

WORKING TECHNIQUES

Limbing

When limbing thick branches you should use the same approach as for cutting.

Cut difﬁcult branches piece by piece.

12

3

Cutting

WARNING! Never attempt to cut logs

! while they are in a pile or when a couple of logs are lying together. Such procedures drastically increase the risk of kickback which can result in a serious or fatal injury.

If you have a pile of logs, each log you attempt to cut should be removed from the pile, placed on a saw horse or runners and cut individually.

Remove the cut pieces from the cutting area. By leaving them in the cutting area, you increase the risk for inadvertently getting a kickback, as well as increasing the risk of losing your balance while working.

The log is lying on the ground. There is little risk of the chain jamming or the object splitting. However there is a risk that the chain will touch the ground when you ﬁnish the cut.

Cut all the way through the log from above. Avoid letting the chain touch the ground as you ﬁnish the cut. Maintain full throttle but be prepared for what might happen.

If it is possible (can you turn the log?) stop cutting about 2/3 of the way through the log.

Turn the log and ﬁnish the cut from the opposite side.

The log is supported at one end. There is a high risk that it will split.

Start by cutting from below (about 1/3 of the way through).

Finish by cutting from above so that the two cuts meet.

The log is supported at both ends. There is a high risk that the chain will jam.

Start by cutting from above (about 1/3 of the way through).

Finish by cutting from below so that the two cuts meet.

24 – English

Image 24

Contents 570 576 XP KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawMachine′s safety equipment Always use common sensePersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Throttle lockout Chain catcherRight hand guard Stop switch Cutting equipmentVibration damping system MufﬂerCutting equipment designed to reduce kickback BarChain Injuries Some terms that describe the bar and chainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment Which could lead to serious, even fatal injuries Chain oilFilling with chain oil Checking chain lubricationChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Assembly Fitting the bar and chainFitting a spike bumper Working with the chainFuel Handling FuelFuel safety FuellingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique TermsLimbing Tree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cutFreeing a tree that has fallen badly Freeing a trapped treeCutting trees and branches that are in tension How to avoid kickback What is kickback?General advice Cutting the trunk into logsMaintenance Carburettor adjustmentGeneral Correctly adjusted carburettor High speed jet HChecking brake band wear Checking the front hand guardChecking the inertia brake release ImmediatelyMufﬂer Starter Changing a broken or worn starter cordTensioning the recoil spring Changing a broken recoil springAir ﬁlter Spark plugLubricating the bar tip sprocket Adjustment of the oil pump Air Injection centrifugal cleaningRunning when making adjustments Needle bearing lubricationWinter use Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain ﬁling and ﬁle gauges EC-declaration of conformityApplies to Europe only EN ISO 12100-22003, Cispr 122001, EN ISOPage Page ´z+SÆ6¶6w¨ Page 1151002-26