Husqvarna 570 576 XP manual General Safety Precautions

Page 8

GENERAL SAFETY PRECAUTIONS

•The chain brake (A) can either be activated manually (by your left hand) or automatically by the inertia release mechanism.

•The brake is applied when the front hand guard (B) is pushed forwards.

•This movement activates a spring-loaded mechanism that tightens the brake band (C) around the engine drive system (D) (clutch drum).

•The front hand guard is not designed solely to activate the chain brake. Another important feature is that it reduces the risk of your left hand hitting the chain if you lose grip of the front handle.

•The chain brake must be engaged when the chain saw is started to prevent the saw chain from rotating.

•Use the chain brake as a ”parking brake” when starting and when moving over short distances, to reduce the risk of moving chain accidentally hitting your leg or anyone or anything close by.

8 – English

•To release the chain brake pull the front hand guard backwards, towards the front handle.

•Kickback can be very sudden and violent. Most kickbacks are minor and do not always activate the chain brake. If this happens you should hold the chain saw ﬁrmly and not let go.

•The way the chain brake is activated, either manually or automatically by the inertia release mechanism, depends on the force of the kickback and the position of the chain saw in relation to the object that the kickback zone of the bar strikes.

If you get a violent kickback while the kickback zone of the bar is farthest away from you the chain brake is designed to be activated by the inertia in the kickback direction.

If the kickback is less violent or the kickback zone of the bar is closer to you the chain brake will be activated manually by the movement of your left hand.

•In the felling position the left hand is in a position that makes manual activation of the chain brake impossible. With this type of grip, that is when the left hand is placed so that it cannot affect the movement

Image 8

Contents 570 576 XP Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawMachine′s safety equipment Always use common sensePersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Right hand guard Throttle lockoutChain catcher Stop switch Cutting equipmentVibration damping system MufﬂerCutting equipment designed to reduce kickback BarChain Injuries Some terms that describe the bar and chainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment Which could lead to serious, even fatal injuries Chain oilFilling with chain oil Checking chain lubricationChecking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Assembly Fitting the bar and chainFitting a spike bumper Working with the chainFuel Handling FuelFuel safety FuellingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique TermsLimbing Tree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cutCutting trees and branches that are in tension Freeing a tree that has fallen badlyFreeing a trapped tree How to avoid kickback What is kickback?General advice Cutting the trunk into logsGeneral MaintenanceCarburettor adjustment Correctly adjusted carburettor High speed jet HChecking brake band wear Checking the front hand guardChecking the inertia brake release ImmediatelyMufﬂer Starter Changing a broken or worn starter cordTensioning the recoil spring Changing a broken recoil springLubricating the bar tip sprocket Air ﬁlterSpark plug Adjustment of the oil pump Air Injection centrifugal cleaningRunning when making adjustments Needle bearing lubricationWinter use Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain ﬁling and ﬁle gauges EC-declaration of conformityApplies to Europe only EN ISO 12100-22003, Cispr 122001, EN ISOPage Page ´z+SÆ6¶6w¨ Page 1151002-26