Husqvarna 570 576 XP manual Starter, Changing a broken or worn starter cord, Fitting the starter

Page 33

MAINTENANCE

Starter

WARNING! When the recoil spring is ! wound up in the starter housing it is

under tension and can, if handled carelessly, pop out and cause personal injury.

Care must be exercised when replacing the return spring or the starter cord. Wear protective glasses and protective gloves.

Changing a broken or worn starter cord

•Loosen the screws that hold the starter against the crankcase and remove the starter.

•Pull out the cord approx. 30 cm and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the pulley rotate slowly backwards.

12

•Undo the screw in the centre of the pulley and remove the pulley. Insert and fasten a new starter cord to the pulley. Wind approx. 3 turns of the starter cord onto the pulley. Connect the pulley to the recoil spring so that the end of the spring engages in the pulley. Fit the screw in the centre of the pulley. Insert the starter cord through the hole in the starter housing and the starter handle. Make a secure knot in the end of the starter cord.

Tensioning the recoil spring

•Hook the starter cord in the notch in the pulley and turn the starter pulley about 2 turns clockwise.

Note! Check that the pulley can be turned at least a further 1/2 turn when the starter cord is pulled all the way out.

1

2

Changing a broken recoil spring

•Lift off the pulley. See instructions under heading Changing a broken or worn starter cord.

•Remove the recoil spring from inside the pulley by tapping the pulley lightly with its inside face downwards against a work bench or the like. If the spring pops out during ﬁtting, wind it up again, working from the outside in towards centre.

•Lubricate the recoil spring with light oil. Fit the pulley and tension the recoil spring.

Fitting the starter

•To ﬁt the starter, ﬁrst pull out the starter cord and place the starter in position against the crankcase. Then slowly release the starter cord so that the pulley engages with the pawls.

•Fit and tighten the screws that hold the starter.

English – 33

Image 33

Contents 570 576 XP KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Throttle lockout Chain catcherRight hand guard Cutting equipment Stop switchVibration damping system MufﬂerBar Cutting equipment designed to reduce kickbackChain Injuries Some terms that describe the bar and chainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain Which could lead to serious, even fatal injuries Chain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Fitting the bar and chain AssemblyFitting a spike bumper Working with the chainFuel Fuel HandlingFuelling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules Terms Basic cutting techniqueLimbing Safe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatFelling cut Directional cutsFreeing a tree that has fallen badly Freeing a trapped treeCutting trees and branches that are in tension What is kickback? How to avoid kickbackGeneral advice Cutting the trunk into logsMaintenance Carburettor adjustmentGeneral High speed jet H Correctly adjusted carburettorChecking brake band wear Checking the front hand guardImmediately Checking the inertia brake releaseMufﬂer Changing a broken or worn starter cord StarterTensioning the recoil spring Changing a broken recoil springAir ﬁlter Spark plugLubricating the bar tip sprocket Air Injection centrifugal cleaning Adjustment of the oil pumpRunning when making adjustments Needle bearing lubricationHeated handles Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain ﬁling and ﬁle gauges EC-declaration of conformity Bar and chain combinationsApplies to Europe only EN ISO 12100-22003, Cispr 122001, EN ISOPage Page ´z+SÆ6¶6w¨ Page 1151002-26