Husqvarna 570, 575XP manual Tensioning the chain, General advice on adjusting depth gauge setting

Page 13

GENERAL SAFETY PRECAUTIONS

General advice on adjusting depth gauge setting

•When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. To maintain optimal cutting performance the depth gauge (B) has to be filed down to achieve the recommended depth gauge setting.

See instructions under the heading Technical data to find the correct depth gauge setting for your particular chain.

WARNING! The risk of kickback is increased

!if the depth gauge setting is too large!

Adjustment of depth gauge setting

•The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

•You will need a flat file and a depth gauge tool. We recommend that you use our depth gauge tool to acheive the correct depth gauge setting and bevel for the depth gauge.

•Place the depth gauge tool over the chain. Detailed information regarding the use of the depth gauge tool, will be found on the package for the depth gauge tool. Use the flat file to file off the tip of the depth gauge that protrudes through the depth gauge tool. The depth gauge setting is correct when you no longer feel resistance as you draw the file along the depth gauge tool.

Tensioning the chain

WARNING! A slack chain may jump off the

!bar and cause serious or even fatal injury.

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

•Loosen the bar nuts that hold the clutch cover/chain brake. Use the combination spanner. Then tighten the bar nuts by hand as tight as you can.

•Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar.

•Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar.

The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under the heading What is what? to find out where it is on your model.

English – 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 570 575XP Key to symbols KEY to SymbolsYou will find the following labels on your chain saw Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockRight hand guard Vibration damping systemCutting equipment Stop switchMuffler General rulesBar Cutting equipment designed to reduce kickbackChain Some terms that describe the bar and chainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingSharpening cutting teeth Instructions considerably increases the risk of kickbackAdjustment of depth gauge setting General advice on adjusting depth gauge settingIf the depth gauge setting is too large Tensioning the chainChain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationChecking wear on cutting equipment Needle bearing lubricationFitting the bar and chain AssemblyFuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules General Basic cutting techniqueTerms Cutting LimbingSafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatDirectional cuts FellingFelling cut Freeing a trapped tree Freeing a tree that has fallen badlyWhat is kickback? How to avoid kickbackGeneral advice Cutting trees and branches that are in tensionCutting the trunk into logs Carburetor adjustment MaintenanceGeneral High speed jet H Correctly adjusted carburetorChecking brake band wear Checking the front hand guardChecking the inertia brake release When the bar hits the stump the brake should be appliedChecking the brake trigger Muffler Changing a broken or worn starter cord StarterTensioning the recoil spring Changing a broken recoil springSpark plug Air filterLubricating the bar tip sprocket Needle bearing lubricationAir Injection centrifugal cleaning Adjustment of the oil pumpWhen making adjustments Cooling systemHeated handles Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataTechnical Data Your Warranty Rights and Obligations Federal Emission Control Warranty StatementSafety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautionsPage 1140240-95 ´z+H8¶5m¨ ´z+H8¶5m¨

570, 575XP specifications

The Husqvarna 570 and 575XP chainsaws are remarkable tools designed for professional logger and forestry applications. Built for performance, durability, and ease of use, both models are engineered to handle the demands of heavy-duty cutting tasks while delivering outstanding power-to-weight ratios.

One of the standout features of the Husqvarna 570 is its X-Torq engine technology, which is designed to provide increased power while reducing fuel consumption and emissions. This engine technology allows the chainsaw to operate more efficiently, making it an environmentally friendly choice for users who are conscious about their impact on nature. The 575XP model also comes equipped with the X-Torq engine, delivering exceptional performance in a compact design.

Both models feature Husqvarna’s Air Injection system, which helps to minimize wear and tear by filtering out larger particles before they reach the air filter. This not only extends the life of the air filter but also allows for longer operating times between cleanings, thus improving overall efficiency.

The ergonomic design of the Husqvarna 570 and 575XP enhances operator comfort and control. The chainsaws come with a low-vibration system, which significantly reduces vibrations felt by the operator, making extended use more comfortable. The front and rear handles are designed for optimal grip, allowing for better maneuverability and reducing operator fatigue during prolonged cutting sessions.

Another key characteristic is the quick-release air filter, which allows for easy access for maintenance. This feature is particularly beneficial for professionals who need to ensure their equipment remains in peak condition.

In terms of safety, both models include a chain brake that provides instant stopping capabilities for added security during operation. This is a crucial feature when working in potentially hazardous environments.

With their combination of innovative technologies, ergonomic design, and robust performance, the Husqvarna 570 and 575XP chainsaws stand out in the market as reliable tools for professionals needing efficiency and power. Whether tackling large trees or performing forestry maintenance, these chainsaws are designed to deliver exceptional results.
Top Page Image Contents