Husqvarna 570, 575XP manual Lubricating cutting equipment, Chain oil, Filling with chain oil

Page 14

GENERAL SAFETY PRECAUTIONS

Lubricating cutting equipment

WARNING! Poor lubrication of cutting

!equipment may cause the chain to snap, which could lead to serious, even fatal injuries.

Chain oil

Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather.

As a chain saw manufacturer we have developed an optimal chain oil which has a vegetable oil base. We recommend the use of our own oil for both maximum chain life and to minimise environmental damage. If our own chain oil is not available, standard chain oil is recommended.

Never use waste oil! Using waste oil can be dangerous to you and damage the machine and environment.

IMPORTANT! When using vegetable based saw chain oil, dismantle and clean the groove in the bar and saw chain before long-term storage. Otherwise there is a risk of the saw chain oil oxidizing, which will result in the saw chain becoming stiff and the bar tip sprocket jamming.

Filling with chain oil

•All our chain saws have an automatic chain lubrication system. On some models the oil flow is also adjustable.

•The saw chain oil tank and the fuel tank are designed so that the fuel runs out before the saw chain oil.

However, this safety feature requires that you use the right sort of chain oil (if the oil is too thin it will run out before the fuel), and that you adjust the carburetor as recommended (a lean mixture may mean that the fuel lasts longer than the oil) and that you also use the recommended cutting equipment (a bar that is too long will use more chain oil).

Checking chain lubrication

•Check the chain lubrication each time you refuel.

Aim the tip of the bar at a light coloured surface about 20 cm (8 inches) away. After 1 minute running at 3/4 throttle you should see a distinct line of oil on the light surface.

If the chain lubrication is not working:

•Check that the oil channel in the bar is not obstructed. Clean if necessary.

•Check that the groove in the edge of the bar is clean. Clean if necessary.

•Check that the bar tip sprocket turns freely and that the lubricating hole in the tip sprocket is not blocked. Clean and lubricate if necessary.

If the chain lubrication system is still not working after carrying out the above checks and associated measures you should contact your servicing dealer.

Chain drive sprocket

The clutch drum is fitted with one of the following drive sprockets:

ASpur sprocket (the chain sprocket is welded on the drum)

BRim sprocket (replaceable)

Regularly check the degree of wear on the drive sprocket. Replace if wear is excessive. Replace the drive sprocket whenever you replace the chain.

14 – English

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 570 575XP You will find the following labels on your chain saw KEY to SymbolsKey to symbols Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Right hand guard Throttle lockChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesChain Cutting equipment designed to reduce kickbackBar Some terms that describe the bar and chainSharpening cutting teeth Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Instructions considerably increases the risk of kickbackIf the depth gauge setting is too large General advice on adjusting depth gauge settingAdjustment of depth gauge setting Tensioning the chainFilling with chain oil Lubricating cutting equipmentChain oil Checking chain lubricationNeedle bearing lubrication Checking wear on cutting equipmentAssembly Fitting the bar and chainFuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Terms Basic cutting techniqueGeneral Limbing CuttingFelling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatFelling cut FellingDirectional cuts Freeing a tree that has fallen badly Freeing a trapped treeGeneral advice How to avoid kickbackWhat is kickback? Cutting trees and branches that are in tensionCutting the trunk into logs General MaintenanceCarburetor adjustment Checking brake band wear Correctly adjusted carburetorHigh speed jet H Checking the front hand guardChecking the brake trigger When the bar hits the stump the brake should be appliedChecking the inertia brake release Muffler Tensioning the recoil spring StarterChanging a broken or worn starter cord Changing a broken recoil springLubricating the bar tip sprocket Air filterSpark plug Needle bearing lubricationWhen making adjustments Adjustment of the oil pumpAir Injection centrifugal cleaning Cooling systemWinter use Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataTechnical Data Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage 1140240-95 ´z+H8¶5m¨ ´z+H8¶5m¨

570, 575XP specifications

The Husqvarna 570 and 575XP chainsaws are remarkable tools designed for professional logger and forestry applications. Built for performance, durability, and ease of use, both models are engineered to handle the demands of heavy-duty cutting tasks while delivering outstanding power-to-weight ratios.

One of the standout features of the Husqvarna 570 is its X-Torq engine technology, which is designed to provide increased power while reducing fuel consumption and emissions. This engine technology allows the chainsaw to operate more efficiently, making it an environmentally friendly choice for users who are conscious about their impact on nature. The 575XP model also comes equipped with the X-Torq engine, delivering exceptional performance in a compact design.

Both models feature Husqvarna’s Air Injection system, which helps to minimize wear and tear by filtering out larger particles before they reach the air filter. This not only extends the life of the air filter but also allows for longer operating times between cleanings, thus improving overall efficiency.

The ergonomic design of the Husqvarna 570 and 575XP enhances operator comfort and control. The chainsaws come with a low-vibration system, which significantly reduces vibrations felt by the operator, making extended use more comfortable. The front and rear handles are designed for optimal grip, allowing for better maneuverability and reducing operator fatigue during prolonged cutting sessions.

Another key characteristic is the quick-release air filter, which allows for easy access for maintenance. This feature is particularly beneficial for professionals who need to ensure their equipment remains in peak condition.

In terms of safety, both models include a chain brake that provides instant stopping capabilities for added security during operation. This is a crucial feature when working in potentially hazardous environments.

With their combination of innovative technologies, ergonomic design, and robust performance, the Husqvarna 570 and 575XP chainsaws stand out in the market as reliable tools for professionals needing efficiency and power. Whether tackling large trees or performing forestry maintenance, these chainsaws are designed to deliver exceptional results.
Top Page Image Contents