Husqvarna 570, 575XP manual How to avoid kickback, What is kickback?, General advice

Page 28

WORKING TECHNIQUES

Cutting trees and branches that are in tension

Preparations: Work out which side is in tension and where the point of maximum tension is (i.e. where it would break if it was bent even more).

Decide which is the safest way to release the tension and whether you are able to do it safely. In complicated situations the only safe method is to put aside your chain saw and use a winch.

General advice:

Position yourself so that you will be clear of the tree or branch when the tension is released.

Make one or more cuts at or near the point of maximum tension. Make as many cuts of sufficient depth as necessary to reduce the tension and make the tree or branch break at the point of maximum tension.

Never cut straight through a tree or branch that is in tension!

If you must cut across tree/limb, make two to three cuts, one inch apart, one to two inches deep.

Continue to cut deeper until tree/limb bends and tension is released.

Cut tree/limb from outside the bend, after tension has been released.

How to avoid kickback

WARNING! Kickback can happen very

!suddenly and violently; kicking the chain saw, bar and chain back at the user. If this happens when the chain is moving it can cause very serious, even fatal injuries. It is vital you understand what causes kickback and that you can avoid it by taking care and using the right working technique.

What is kickback?

The word kickback is used to describe the sudden reaction that causes the chain saw and bar to jump off an object when the upper quadrant of the tip of the bar, known as the kickback zone, touches an object.

Kickback always occurs in the cutting plane of the bar. Normally the chain saw and bar are thrown backwards and upwards towards the user. However, the chain saw may move in a different direction depending on the way it was being used when the kickback zone of the bar touched the object.

Kickback only occurs if the kickback zone of the bar touches an object.

28 – English

Page 27 Page 29
Image 28
Page 27 Page 29
Contents 570 575XP Key to symbols KEY to SymbolsYou will find the following labels on your chain saw Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Throttle lock Chain catcherRight hand guard Vibration damping systemStop switch Cutting equipmentMuffler General rulesCutting equipment designed to reduce kickback BarChain Some terms that describe the bar and chainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethSharpening cutting teeth Instructions considerably increases the risk of kickbackGeneral advice on adjusting depth gauge setting Adjustment of depth gauge settingIf the depth gauge setting is too large Tensioning the chainLubricating cutting equipment Chain oilFilling with chain oil Checking chain lubricationNeedle bearing lubrication Checking wear on cutting equipmentAssembly Fitting the bar and chainFuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules General Basic cutting techniqueTerms Limbing CuttingTree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts FellingFelling cut Freeing a tree that has fallen badly Freeing a trapped treeHow to avoid kickback What is kickback?General advice Cutting trees and branches that are in tensionCutting the trunk into logs Carburetor adjustment MaintenanceGeneral Correctly adjusted carburetor High speed jet HChecking brake band wear Checking the front hand guardChecking the inertia brake release When the bar hits the stump the brake should be appliedChecking the brake trigger Muffler Starter Changing a broken or worn starter cordTensioning the recoil spring Changing a broken recoil springAir filter Spark plugLubricating the bar tip sprocket Needle bearing lubricationAdjustment of the oil pump Air Injection centrifugal cleaningWhen making adjustments Cooling systemWinter use Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataTechnical Data Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautionsPage 1140240-95 ´z+H8¶5m¨ ´z+H8¶5m¨

570, 575XP specifications

The Husqvarna 570 and 575XP chainsaws are remarkable tools designed for professional logger and forestry applications. Built for performance, durability, and ease of use, both models are engineered to handle the demands of heavy-duty cutting tasks while delivering outstanding power-to-weight ratios.

One of the standout features of the Husqvarna 570 is its X-Torq engine technology, which is designed to provide increased power while reducing fuel consumption and emissions. This engine technology allows the chainsaw to operate more efficiently, making it an environmentally friendly choice for users who are conscious about their impact on nature. The 575XP model also comes equipped with the X-Torq engine, delivering exceptional performance in a compact design.

Both models feature Husqvarna’s Air Injection system, which helps to minimize wear and tear by filtering out larger particles before they reach the air filter. This not only extends the life of the air filter but also allows for longer operating times between cleanings, thus improving overall efficiency.

The ergonomic design of the Husqvarna 570 and 575XP enhances operator comfort and control. The chainsaws come with a low-vibration system, which significantly reduces vibrations felt by the operator, making extended use more comfortable. The front and rear handles are designed for optimal grip, allowing for better maneuverability and reducing operator fatigue during prolonged cutting sessions.

Another key characteristic is the quick-release air filter, which allows for easy access for maintenance. This feature is particularly beneficial for professionals who need to ensure their equipment remains in peak condition.

In terms of safety, both models include a chain brake that provides instant stopping capabilities for added security during operation. This is a crucial feature when working in potentially hazardous environments.

With their combination of innovative technologies, ergonomic design, and robust performance, the Husqvarna 570 and 575XP chainsaws stand out in the market as reliable tools for professionals needing efficiency and power. Whether tackling large trees or performing forestry maintenance, these chainsaws are designed to deliver exceptional results.
Top Page Image Contents