Husqvarna 55 EPA I manual Lubricating cutting equipment, Chain oil, Filling with chain oil

Page 14

GENERAL SAFETY PRECAUTIONS

Lubricating cutting equipment

WARNING! Poor lubrication of cutting

!equipment may cause the chain to snap, which could lead to serious, even fatal injuries.

Chain oil

Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather.

As a chain saw manufacturer we have developed an optimal chain oil which has a vegetable oil base. We recommend the use of our own oil for both maximum chain life and to minimise environmental damage. If our own chain oil is not available, standard chain oil is recommended.

Never use waste oil! Using waste oil can be dangerous to you and damage the machine and environment.

IMPORTANT! When using vegetable based saw chain oil, dismantle and clean the groove in the bar and saw chain before long-term storage. Otherwise there is a risk of the saw chain oil oxidizing, which will result in the saw chain becoming stiff and the bar tip sprocket jamming.

Filling with chain oil

•All our chain saws have an automatic chain lubrication system. On some models the oil flow is also adjustable.

•The saw chain oil tank and the fuel tank are designed so that the fuel runs out before the saw chain oil.

However, this safety feature requires that you use the right sort of chain oil (if the oil is too thin it will run out before the fuel), and that you adjust the carburetor as recommended (a lean mixture may mean that the fuel lasts longer than the oil) and that you also use the recommended cutting equipment (a bar that is too long will use more chain oil).

Checking chain lubrication

•Check the chain lubrication each time you refuel. See instructions under the heading Lubricating the bar tip sprocket.

Aim the tip of the bar at a light coloured surface about 20 cm (8 inches) away. After 1 minute running at 3/4 throttle you should see a distinct line of oil on the light surface.

If the chain lubrication is not working:

•Check that the oil channel in the bar is not obstructed. Clean if necessary.

•Check that the groove in the edge of the bar is clean. Clean if necessary.

•Check that the bar tip sprocket turns freely and that the lubricating hole in the tip sprocket is not blocked. Clean and lubricate if necessary.

If the chain lubrication system is still not working after carrying out the above checks and associated measures you should contact your servicing dealer.

14 – English

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Operator’s manual 55 EPA Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Right hand guard Throttle lockChain catcher Vibration damping system Stop switchCutting equipment MufflerBar General rulesCutting equipment designed to reduce kickback ChainSharpening cutting teeth Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Tensioning the chain General advice on adjusting depth gauge settingAdjustment of depth gauge setting Filling with chain oil Lubricating cutting equipmentChain oil Checking chain lubricationChecking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Assembly Fitting the bar and chainFuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Terms Basic cutting techniqueGeneral Limbing CuttingFelling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatFelling Directional cutsFreeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Checking the front hand guard Correctly adjusted carburetorChecking brake band wear Checking the inertia brake releaseThrottle lock Changing a broken or worn starter cord MufflerStarter Changing a broken recoil spring Air filterTensioning the recoil spring Fitting the starterNeedle bearing lubrication Spark plugLubricating the bar tip sprocket Cooling systemTemperature 0C 32F or colder Winter useMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gauges Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautions´z+R7y¶5m¨ Page 1150238-95 ´z+R7y¶5m¨ ´z+R7y¶5m¨
Top Page Image Contents