Husqvarna 55 EPA I manual Starting and Stopping, Starting and stopping, Cold engine, Warm engine

Page 19

STARTING AND STOPPING

Starting and stopping

WARNING! Note the following before

!starting:

Never start a chain saw unless the bar, chain and all covers are fitted correctly. Otherwise the clutch can come loose and cause personal injuries.

Always move the machine away from the refuelling area before starting.

Place the machine on firm ground. Make sure you have a secure footing and that the chain cannot touch anything.

Keep people and animals well away from the working area.

Cold engine

Starting: The chain brake should be activated when starting the chain saw. Activate the chain brake by pushing the front hand guard forwards.

Ignition: Slide the ignition switch to the left.

Choke: Set the choke control in the choke position.

Start throttle: The correct choke/start throttle setting is obtained by moving the control to the choke position.

If the machine is fitted with a decompression valve (A): Press the valve to reduce the pressure in the cylinder and make starting easier. You should always use the decompression valve when starting the machine. Once the machine has started the valve will automatically return to its original setting.

A

Warm engine

Use the same starting procedure as for a cold engine but without setting the choke control in the choke position.

Starting

Grip the front handle with your left hand. Hold the chain saw on the ground by placing your right foot through the rear handle. Pull the starter handle with your right hand and pull out the starter cord slowly until you feel a resistance (as the starter pawls engage) then pull firmly and rapidly.Never wrap the starter cord around your hand

As the chain brake is still activated the engine must return to idling speed as soon as possible by disengaging the throttel latch in order to avoid unnecessery wear on the clutch assembly.

Push in the choke control as soon as the engine fire and make repeated starting attempts. Immediately press and release the throttle when the engine starts. That will disengage the throttle latch.

CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine.

English – 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Operator’s manual 55 EPA Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockRight hand guard Muffler Stop switchCutting equipment Vibration damping systemChain General rulesCutting equipment designed to reduce kickback BarGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingSharpening cutting teeth Adjustment of depth gauge setting General advice on adjusting depth gauge settingTensioning the chain Checking chain lubrication Lubricating cutting equipmentChain oil Filling with chain oilNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyFuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules General Basic cutting techniqueTerms Cutting LimbingClearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionDirectional cuts FellingCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral Checking the inertia brake release Correctly adjusted carburetorChecking brake band wear Checking the front hand guardThrottle lock Starter MufflerChanging a broken or worn starter cord Fitting the starter Air filterTensioning the recoil spring Changing a broken recoil springCooling system Spark plugLubricating the bar tip sprocket Needle bearing lubricationWinter use Temperature 0C 32F or colderDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataBar and chain combinations Saw chain filing and file gauges Your Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautions´z+R7y¶5m¨ Page 1150238-95 ´z+R7y¶5m¨ ´z+R7y¶5m¨
Top Page Image Contents