Husqvarna 55 EPA I manual Assembly, Fitting the bar and chain

Page 16

ASSEMBLY

Fitting the bar and chain

WARNING! Always wear gloves, when

!working with the chain, in order to protect your hands from injury.

Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle.

Remove the bar nuts and remove the clutch cover (chain brake). Take off the transportation ring (A).

Fit the bar over the bar bolts. Place the bar in its rearmost position. Place the chain over the drive sprocket locate it in the groove on the bar. Begin on the top edge of the bar. Make sure that the edges of the cutting links are facing forward on the top edge of the bar.

Fit the clutch cover and locate the chain adjuster pin in the hole in the bar. Check that the drive links of the chain ﬁt correctly over the drive sprocket and that the chain is correctly located in the groove in the bar. Tighten the bar nuts ﬁnger tight.

Tension the chain by turning the chain tensioning screw clockwise using the combination spanner.

The chain is correctly tensioned when it does not sag from the underside of the bar, but can still be turned easily by hand. Hold up the bar tip and tighten the bar nuts with the combination spanner.

When ﬁtting a new chain, the chain tension has to be checked frequently until the chain is run-in. Check the chain tension regularly. A correctly tensioned chain ensures good cutting performance and long life.

Note! If clutch cover is difﬁcult to remove, replace bar nuts, engage brake and rerelease (an audible click will be heard if released properly).

16 – English

Image 16

Contents Operator’s manual 55 EPA Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockRight hand guard Stop switch Cutting equipmentVibration damping system MufﬂerGeneral rules Cutting equipment designed to reduce kickbackBar ChainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingSharpening cutting teeth Adjustment of depth gauge setting General advice on adjusting depth gauge settingTensioning the chain Lubricating cutting equipment Chain oilFilling with chain oil Checking chain lubricationNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Assembly Fitting the bar and chainFuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules General Basic cutting techniqueTerms Limbing CuttingTree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatFelling Directional cutsGeneral advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral Correctly adjusted carburetor Checking brake band wearChecking the front hand guard Checking the inertia brake releaseThrottle lock Starter MufﬂerChanging a broken or worn starter cord Air ﬁlter Tensioning the recoil springChanging a broken recoil spring Fitting the starterSpark plug Lubricating the bar tip sprocketNeedle bearing lubrication Cooling systemTemperature 0C 32F or colder Winter useMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain ﬁling and ﬁle gauges Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautions´z+R7y¶5m¨ Page 1150238-95 ´z+R7y¶5m¨ ´z+R7y¶5m¨