Husqvarna 455e Rancher Spark plug, Lubricating the bar tip sprocket, Needle bearing lubrication

Page 36

MAINTENANCE

Spark plug

The spark plug condition is influenced by:

•Incorrect carburetor adjustment.

•An incorrect fuel mixture (too much or incorrect type of oil).

•A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.5 mm (0,020"). The spark plug should be replaced after about a month in operation or earlier if necessary.

Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

Lubricating the bar tip sprocket

Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease.

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regularly (once a week).

When lubricating, remove the clutch cover by loosening the two bar nuts. Lay the saw on its side with the clutch drum upwards.

Lubrication involves engine oil dripping into the centre of the clutch drum as it rotates.

Adjustment of the oil pump

Adjustments are made by turning the screw using a screwdriver or combination spanner. The machine is supplied from the factory with the screw set to position 2. Turning the screw clockwise will reduce the oil flow and turning the screw anti-clockwise will increase the oil flow.

Recommended settings:

Bar 13"-15": Position 1

Bar 15"-18": Position 2

Bar 18"-20": Position 3

These recommendations apply to Husqvarna’s chain oil, for other chain oils increase the oil flow by one step.

WARNING! The engine must be stopped

!when making adjustments.

36 – English

Page 35 Page 37
Image 36
Page 35 Page 37
Contents 455e Rancher KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Throttle lockout Chain catcherRight hand guard Stop switch Cutting equipmentVibration damping system MufflerGeneral rules Cutting equipment designed to reduce kickbackBar ChainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethSharpening cutting teeth General advice on adjusting depth gauge setting Adjustment of depth gauge settingTensioning the chain RancherLubricating cutting equipment 455e RancherChain oil Filling with chain oilChecking chain lubrication Chain drive sprocketNeedle bearing lubrication Checking wear on cutting equipmentBar Assembly Fitting the bar and chainRancher 455e RancherAssembly Fuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique GeneralTerms Limbing CuttingTree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatFelling Directional cutsGeneral advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Correctly adjusted carburetor High speed jet HChecking brake band wear Checking the front hand guardChecking the brake trigger Muffler StarterChanging a broken or worn starter cord Air filter Tensioning the recoil springChanging a broken recoil spring Fitting the starterAdjustment of the oil pump Spark plugLubricating the bar tip sprocket Needle bearing lubricationAir Injection centrifugal cleaning Temperature 0C 32F or colderTemperature -5C 23F or colder Cooling systemMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautionsPage 1150250-95 ´z+R9¶53¨ ´z+R9¶53¨

455e Rancher specifications

The Husqvarna 455e Rancher is a powerful and versatile chainsaw designed for homeowners and professionals alike. This robust equipment is particularly suited for cutting tasks involving firewood, felling small to medium-sized trees, and general property maintenance. Its blend of efficiency, durability, and user-friendly features makes it a popular choice among users.

One of the defining features of the 455e Rancher is its engine, which is a 55.5cc, 2-stroke gas engine that delivers significant power while maintaining a lightweight design. The engine is engineered to be fuel-efficient, allowing users to achieve more cutting time with less refueling. The chainsaw boasts a maximum power output of 3.4 horsepower, ensuring that it can handle heavier loads without straining.

Another significant innovation in the Husqvarna 455e Rancher is the X-Torq technology. This unique system lowers fuel consumption and reduces harmful emissions, making it an environmentally friendly option without sacrificing performance. The chainsaw is also equipped with a LowVib system that minimizes vibration, allowing for extended use without causing fatigue to the operator. This feature contributes to increased comfort and control, making it suitable for prolonged cutting sessions.

The chainsaw features a quick-release air filter that simplifies maintenance. This air filter system keeps debris out of the engine, ensuring optimal performance and longevity. The tool-less chain tensioning system allows users to easily adjust the chain without the need for additional tools, making it convenient and time-efficient.

Safety is a priority with the 455e Rancher, which includes several protective features. The chainsaw comes equipped with a chain brake that automatically activates in case of kickback, reducing the risk of injury. Additionally, the chainsaw's ergonomic design facilitates a secure grip, enhancing safety during operation.

Overall, the Husqvarna 455e Rancher combines power, efficiency, and safety, making it a reliable choice for various cutting tasks. Whether you're a casual user or a seasoned professional, the 455e Rancher provides robust performance and dependable features to handle your landscaping challenges effectively. Its customer-friendly design ensures that it remains a preferred choice in the world of chainsaws.
Top Page Image Contents