Husqvarna 455e Rancher Tensioning the chain, General advice on adjusting depth gauge setting

Page 13

GENERAL SAFETY PRECAUTIONS

•File all the teeth to the same length. When the length of the cutting teeth is reduced to 4 mm (0.16") the chain is worn out and should be replaced.

General advice on adjusting depth gauge setting

•When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. To maintain optimal cutting performance the depth gauge (B) has to be filed down to achieve the recommended depth gauge setting. See instructions under the heading Technical data to find the correct depth gauge setting for your particular chain.

WARNING! The risk of kickback is increased

!if the depth gauge setting is too large!

Adjustment of depth gauge setting

•The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

•You will need a flat file and a depth gauge tool. We recommend that you use our depth gauge tool to acheive the correct depth gauge setting and bevel for the depth gauge.

•Place the depth gauge tool over the chain. Detailed information regarding the use of the depth gauge tool, will be found on the package for the depth gauge tool. Use the flat file to file off the tip of the depth gauge that protrudes through the depth gauge tool. The depth gauge setting is correct when you no longer feel resistance as you draw the file along the depth gauge tool.

Tensioning the chain

WARNING! A slack chain may jump off the

!bar and cause serious or even fatal injury.

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

455 Rancher, 460

•Loosen the bar nuts that hold the clutch cover/chain brake. Use the combination spanner. Then tighten the bar nuts by hand as tight as you can.

•Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar.

•Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar.

The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under the heading What is what? to find out where it is on your model.

English – 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 455e Rancher Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockoutRight hand guard Cutting equipment Stop switchVibration damping system MufflerCutting equipment designed to reduce kickback General rulesBar ChainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingSharpening cutting teeth Adjustment of depth gauge setting General advice on adjusting depth gauge settingTensioning the chain Rancher455e Rancher Lubricating cutting equipmentChain oil Filling with chain oilChain drive sprocket Checking chain lubricationNeedle bearing lubrication Checking wear on cutting equipmentBar Fitting the bar and chain AssemblyRancher 455e RancherAssembly Fuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules General Basic cutting techniqueTerms Cutting LimbingSafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatDirectional cuts FellingFreeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral High speed jet H Correctly adjusted carburetorChecking brake band wear Checking the front hand guardChecking the brake trigger Starter MufflerChanging a broken or worn starter cord Tensioning the recoil spring Air filterChanging a broken recoil spring Fitting the starterSpark plug Adjustment of the oil pumpLubricating the bar tip sprocket Needle bearing lubricationTemperature 0C 32F or colder Air Injection centrifugal cleaningTemperature -5C 23F or colder Cooling systemDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsYour Warranty Rights and Obligations Federal Emission Control Warranty StatementSafety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautionsPage 1150250-95 ´z+R9¶53¨ ´z+R9¶53¨

455e Rancher specifications

The Husqvarna 455e Rancher is a powerful and versatile chainsaw designed for homeowners and professionals alike. This robust equipment is particularly suited for cutting tasks involving firewood, felling small to medium-sized trees, and general property maintenance. Its blend of efficiency, durability, and user-friendly features makes it a popular choice among users.

One of the defining features of the 455e Rancher is its engine, which is a 55.5cc, 2-stroke gas engine that delivers significant power while maintaining a lightweight design. The engine is engineered to be fuel-efficient, allowing users to achieve more cutting time with less refueling. The chainsaw boasts a maximum power output of 3.4 horsepower, ensuring that it can handle heavier loads without straining.

Another significant innovation in the Husqvarna 455e Rancher is the X-Torq technology. This unique system lowers fuel consumption and reduces harmful emissions, making it an environmentally friendly option without sacrificing performance. The chainsaw is also equipped with a LowVib system that minimizes vibration, allowing for extended use without causing fatigue to the operator. This feature contributes to increased comfort and control, making it suitable for prolonged cutting sessions.

The chainsaw features a quick-release air filter that simplifies maintenance. This air filter system keeps debris out of the engine, ensuring optimal performance and longevity. The tool-less chain tensioning system allows users to easily adjust the chain without the need for additional tools, making it convenient and time-efficient.

Safety is a priority with the 455e Rancher, which includes several protective features. The chainsaw comes equipped with a chain brake that automatically activates in case of kickback, reducing the risk of injury. Additionally, the chainsaw's ergonomic design facilitates a secure grip, enhancing safety during operation.

Overall, the Husqvarna 455e Rancher combines power, efficiency, and safety, making it a reliable choice for various cutting tasks. Whether you're a casual user or a seasoned professional, the 455e Rancher provides robust performance and dependable features to handle your landscaping challenges effectively. Its customer-friendly design ensures that it remains a preferred choice in the world of chainsaws.
Top Page Image Contents