Husqvarna 1153179-26 manual Tensioning the chain, General advice on adjusting depth gauge setting

Page 13

GENERAL SAFETY PRECAUTIONS

•Check that the chain is correctly tensioned. A slack chain will move sideways, making it more difficult to sharpen correctly.

•Always file cutting teeth from the inside face. Reduce the pressure on the return stroke. File all the teeth on one side first, then turn the chain saw over and file the teeth on the other side.

•File all the teeth to the same length. When the length of the cutting teeth is reduced to 4 mm (5/32") the chain is worn out and should be replaced.

General advice on adjusting depth gauge setting

•When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. To maintain optimal cutting performance the depth gauge (B) has to be filed down to achieve the recommended depth gauge setting. See instructions under the heading Technical data to find the correct depth gauge setting for your particular chain.

!

WARNING! The risk of kickback is

increased if the depth gauge setting is

 

too large!

Adjustment of depth gauge setting

•The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

•You will need a flat file and a depth gauge tool. We recommend that you use our depth gauge tool to

acheive the correct depth gauge setting and bevel for the depth gauge.

•Place the depth gauge tool over the chain. Detailed information regarding the use of the depth gauge tool, will be found on the package for the depth gauge tool. Use the flat file to file off the tip of the depth gauge that protrudes through the depth gauge tool. The depth gauge setting is correct when you no longer feel resistance as you draw the file along the depth gauge tool.

Tensioning the chain

 

!

WARNING! A slack chain may jump off

 

and cause serious or even fatal injury.

 

 

 

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

•Undo the bar nuts that hold the clutch cover/chain brake. Use the combination spanner. Then tighten the bar nuts by hand as tight as you can.

•Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the

English – 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Operator′s manual Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutCutting equipment Stop switchRight hand guard Vibration damping systemCutting equipment designed to reduce kickback General rulesGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingSharpening instructions considerably Increases the risk of kickbackAdjustment of depth gauge setting General advice on adjusting depth gauge settingTensioning the chain Too largeWhich could lead to serious, even fatal injuries Chain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment To prolong the life of the bar you should turn it over daily Fitting the bar and chain AssemblyFitting a spike bumper Working with the chainFuel Fuel HandlingFuelling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsCleaning Clutch cover causing the chain toJam. Always stop the engine before Terms Basic cutting techniqueLogs are lying together. Such LimbingOr fatal injury Log is supported at both ends. There is a high riskSafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatYour saw Training we advise you not to fell treesDirectional cuts Felling cutFreeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCarburettor adjustment MaintenanceGeneral Carburettor with movement limitersCorrectly adjusted carburettor Fine adjustment of the idle speed TCarburettor without movement limiters Low speed jet LRpm 357XP 14000 2700 359 13500 Checking the front hand guard Checking brake band wearChecking the inertia brake release Immediately Starter MufflerChanging a broken or worn starter cord Tensioning the recoil spring Air filterChanging a broken recoil spring Fitting the starterSpark plug Adjustment of the oil pumpLubricating the bar tip sprocket Needle bearing lubricationTemperature 0C or colder Air Injection centrifugal cleaningRunning when making adjustments Cooling systemElectrical carburettor heating Heated handles357 XPG, 359 G Daily maintenance Weekly maintenance Monthly maintenance Maintenance schedule357XP 359 Technical dataSaw chain filing and file gauges Bar and chain combinationsApplies to Europe only EC-declaration of conformityEN ISO 12100-22003, Cispr 122005, EN ISO Original instructions 1153179-26

1153179-26 specifications

The Husqvarna 1153179-26 is a powerful and efficient lawn mower designed for homeowners who seek a balance of performance and ease of use. One of the standout features of this model is its lightweight and compact design, making it easy to maneuver around your garden or yard. With a robust engine, it offers reliable performance, delivering the power needed to tackle various types of grass and terrain with ease.

Equipped with a cutting width of 26 inches, the Husqvarna 1153179-26 allows for efficient mowing over larger areas while still being able to navigate tight spots effectively. The adjustable cutting height adds to its versatility, enabling users to choose the perfect length for their lawns, whether they prefer a manicured look or a more natural appearance.

The mower incorporates advanced technologies that enhance its performance and user experience. The Smart Start feature enables quick and easy starting of the engine with minimal effort, so you can get to mowing without wastefully pulling on a cord multiple times. The air injection system ensures that the air filter remains clean, thereby prolonging the life of the engine and reducing maintenance needs.

Another excellent feature of the Husqvarna 1153179-26 is its ergonomic handle design, which allows for comfortable operation, reducing fatigue during extended mowing sessions. This is particularly beneficial for homeowners with larger properties who have to spend considerable time tending to their lawns.

Durability is a key characteristic of this model, as it features a sturdy construction designed to withstand the rigors of frequent use. The mower's materials are engineered to resist wear and damage, ensuring longevity and reliability.

Additionally, the Husqvarna 1153179-26 has a mulching capability, allowing you to recycle grass clippings back into your lawn, promoting healthier growth and reducing waste. This eco-friendly feature not only improves your lawn’s health but also minimizes the need for bagging and disposal.

In conclusion, the Husqvarna 1153179-26 combines portability, power, and advanced technology to provide an exceptional mowing experience. Its lightweight design, powerful engine, and user-friendly features make it an excellent choice for homeowners looking to maintain a beautiful lawn with ease.
Top Page Image Contents