Husqvarna 1153179-26 Spark plug, Lubricating the bar tip sprocket, Needle bearing lubrication

Page 37

MAINTENANCE

against the filter holder. Clean the filter by brushing or shaking it.

The filter can be cleaned more thoroughly by washing it in water and detergent.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced.

A HUSQVARNA chain saw can be equipped with different types of air filter according to working conditions, weather, season, etc. Contact your dealer for advice.

Spark plug

The spark plug condition is influenced by:

•Incorrect carburettor adjustment.

•An incorrect fuel mixture (too much or incorrect type of oil).

•A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.5 mm. The spark plug should be replaced after about a month in operation or earlier if necessary.

Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

Lubricating the bar tip sprocket

Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease.

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regularly (once a week).

When lubricating, remove the clutch cover by loosening the two bar nuts. Lay the saw on its side with the clutch drum upwards.

Lubrication involves grease being squirted into the centre of the crankshaft using a grease gun.

Adjustment of the oil pump

The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner. The machine is supplied from the factory with the screw set to position 2. Turning the screw clockwise

English – 37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Operator′s manual Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutCutting equipment Stop switchRight hand guard Vibration damping systemCutting equipment designed to reduce kickback General rulesGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingSharpening instructions considerably Increases the risk of kickbackAdjustment of depth gauge setting General advice on adjusting depth gauge settingTensioning the chain Too largeWhich could lead to serious, even fatal injuries Chain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment To prolong the life of the bar you should turn it over daily Fitting the bar and chain AssemblyFitting a spike bumper Working with the chainFuel Fuel HandlingFuelling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsCleaning Clutch cover causing the chain toJam. Always stop the engine before Terms Basic cutting techniqueLogs are lying together. Such LimbingOr fatal injury Log is supported at both ends. There is a high riskSafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatYour saw Training we advise you not to fell treesDirectional cuts Felling cutFreeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCarburettor adjustment MaintenanceGeneral Carburettor with movement limitersCorrectly adjusted carburettor Fine adjustment of the idle speed TCarburettor without movement limiters Low speed jet LRpm 357XP 14000 2700 359 13500 Checking the front hand guard Checking brake band wearChecking the inertia brake release Immediately Starter MufflerChanging a broken or worn starter cord Tensioning the recoil spring Air filterChanging a broken recoil spring Fitting the starterSpark plug Adjustment of the oil pumpLubricating the bar tip sprocket Needle bearing lubricationTemperature 0C or colder Air Injection centrifugal cleaningRunning when making adjustments Cooling systemElectrical carburettor heating Heated handles357 XPG, 359 G Daily maintenance Weekly maintenance Monthly maintenance Maintenance schedule357XP 359 Technical dataSaw chain filing and file gauges Bar and chain combinationsApplies to Europe only EC-declaration of conformityEN ISO 12100-22003, Cispr 122005, EN ISO Original instructions 1153179-26

1153179-26 specifications

The Husqvarna 1153179-26 is a powerful and efficient lawn mower designed for homeowners who seek a balance of performance and ease of use. One of the standout features of this model is its lightweight and compact design, making it easy to maneuver around your garden or yard. With a robust engine, it offers reliable performance, delivering the power needed to tackle various types of grass and terrain with ease.

Equipped with a cutting width of 26 inches, the Husqvarna 1153179-26 allows for efficient mowing over larger areas while still being able to navigate tight spots effectively. The adjustable cutting height adds to its versatility, enabling users to choose the perfect length for their lawns, whether they prefer a manicured look or a more natural appearance.

The mower incorporates advanced technologies that enhance its performance and user experience. The Smart Start feature enables quick and easy starting of the engine with minimal effort, so you can get to mowing without wastefully pulling on a cord multiple times. The air injection system ensures that the air filter remains clean, thereby prolonging the life of the engine and reducing maintenance needs.

Another excellent feature of the Husqvarna 1153179-26 is its ergonomic handle design, which allows for comfortable operation, reducing fatigue during extended mowing sessions. This is particularly beneficial for homeowners with larger properties who have to spend considerable time tending to their lawns.

Durability is a key characteristic of this model, as it features a sturdy construction designed to withstand the rigors of frequent use. The mower's materials are engineered to resist wear and damage, ensuring longevity and reliability.

Additionally, the Husqvarna 1153179-26 has a mulching capability, allowing you to recycle grass clippings back into your lawn, promoting healthier growth and reducing waste. This eco-friendly feature not only improves your lawn’s health but also minimizes the need for bagging and disposal.

In conclusion, the Husqvarna 1153179-26 combines portability, power, and advanced technology to provide an exceptional mowing experience. Its lightweight design, powerful engine, and user-friendly features make it an excellent choice for homeowners looking to maintain a beautiful lawn with ease.
Top Page Image Contents