Husqvarna 1153136-95 manual Lubricating cutting equipment

Page 15

GENERAL SAFETY PRECAUTIONS

445, 450

Loosen the bar nut that holds the clutch cover and chain brake. Use the combination spanner. Then retighten the bar nut as tightly as you can by hand.

(27)

Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar. (28)

Use the combination spanner to tighten the bar nut while holding up the tip of the bar. Check that you can pull the saw chain round freely by hand, and that there is no slack on the underside of the bar. (29)

The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under the heading What is what? to find out where it is on your model.

445e, 450e

Release the knob by folding it out. (30)

Turn the knob anti clockwise to loosen the bar cover.

(31)

Adjust the tension on the chain by turning the wheel down (+) for tighter tension and up (-) to loosen the tension. (32)

Tighten the bar clutch by turning the knob clockwise.

(33)

Fold the knob back in to lock the tensioning. (34)

Lubricating cutting equipment

WARNING! Poor lubrication of cutting

! equipment may cause the chain to snap, which could lead to serious, even fatal injuries.

Chain oil

Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather.

As a chain saw manufacturer we have developed an optimal chain oil which has a vegetable oil base. We recommend the use of our own oil for both maximum chain life and to minimise environmental damage. If our own chain oil is not available, standard chain oil is recommended.

Never use waste oil! Using waste oil can be dangerous to you and damage the machine and environment.

IMPORTANT! When using vegetable based saw chain oil, dismantle and clean the groove in the bar and saw chain before long-term storage. Otherwise there is a risk of the saw chain oil oxidizing, which will result in the saw chain becoming stiff and the bar tip sprocket jamming.

Filling with chain oil

All our chain saws have an automatic chain lubrication system. On some models the oil flow is also adjustable.

The saw chain oil tank and the fuel tank are designed so that the fuel runs out before the saw chain oil.

However, this safety feature requires that you use the right sort of chain oil (if the oil is too thin it will run out before the fuel), and that you adjust the carburetor as recommended (a lean mixture may mean that the fuel lasts longer than the oil) and that you also use the recommended cutting equipment (a bar that is too long will use more chain oil).

Checking chain lubrication

Check the chain lubrication each time you refuel. See instructions under the heading Lubricating the bar tip sprocket.

Aim the tip of the bar at a light coloured surface about 20 cm (8 inches) away. After 1 minute running at 3/4 throttle you should see a distinct line of oil on the light surface.

If the chain lubrication is not working:

Check that the oil channel in the bar is not obstructed. Clean if necessary. (35)

Check that the groove in the edge of the bar is clean. Clean if necessary. (36)

Check that the bar tip sprocket turns freely and that the lubricating hole in the tip sprocket is not blocked. Clean and lubricate if necessary. (37)

If the chain lubrication system is still not working after carrying out the above checks and associated measures you should contact your servicing dealer.

Chain drive sprocket

The clutch drum is fitted with one of the following drive sprockets:

ASpur sprocket (the chain sprocket is welded on the drum)

B Rim sprocket (replaceable) (38)

Regularly check the degree of wear on the drive sprocket. Replace if wear is excessive. Replace the drive sprocket whenever you replace the chain.

1153136-95 Rev.2 2010-04-08

English 15

Image 15
Contents 445 445e 450 450e 1153136-95 Rev.2 1153136-95 Rev.2 4243 1153136-95 Rev.2 112 113 KEY to Symbols Symbols on the machine and/or in the manualDecompression valve The valve Contents What is what on the chain saw? IntroductionDear customer Before using a new chain saw General Safety PrecautionsChain brake and front hand guard Machine′s safety equipmentAlways use common sense Personal protective equipmentRight hand guard Stop switchThrottle lockout Chain catcherCutting equipment designed to reduce kickback Cutting equipmentMuffler General rulesTensioning the chain Sharpening your chain and adjusting depth gauge settingLubricating cutting equipment Checking wear on cutting equipment Needle bearing lubrication445e, 450e AssemblyFitting the bar and chain 445Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageStopping Starting and StoppingStarting and stopping StartingGeneral working instructions Basic safety rulesWorking Techniques Before useBasic cutting technique TermsLimbing Clearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionHow to avoid kickback What is kickback?Freeing a tree that has fallen badly Maintenance Carburetor adjustmentGeneral Muffler StarterReplacing the starter cord Needle bearing lubrication Air filterSpark plug Lubricating the bar tip sprocketWinter use Air Injection centrifugal cleaningTemperature -5C 23F or colder Cooling systemDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical Data058/1,5 mm Bar and chain combinationsSaw chain filing and file gauges 050/1,3 mmYour Warranty Rights and Obligations Federal Emission Control Warranty StatementMAINTENANCE, Replacement Repair of EMISSION-RELATED Parts Other safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautions1153136-95 Rev.2 Original instructions 1153136-95

1153136-95 specifications

The Husqvarna 1153136-95 is a high-performance chainsaw designed for ease of use and efficiency, making it an ideal choice for both residential and professional users. Known for its robust build and reliability, this chainsaw is particularly well-suited for tasks such as tree pruning, cutting firewood, and managing landscaping projects.

One of the standout features of the Husqvarna 1153136-95 is its lightweight design. Weighing in at just around 10 lbs, it allows users to easily maneuver during extended periods of operation without causing excessive fatigue. This is complemented by an ergonomic handle that provides a comfortable grip, reducing strain on the hands and wrists.

The chainsaw is powered by an efficient and reliable engine. With a displacement of 38.2 cc, it delivers ample power for most cutting tasks while maintaining fuel efficiency. The technology incorporated into its engine design ensures lower emissions, making it an environmentally friendly option in the category of gas-powered chainsaws.

Another impressive feature of the Husqvarna 1153136-95 is the X-Torq technology. This innovatively engineered system reduces fuel consumption by up to 20%, resulting in longer runtimes between refueling. Additionally, it minimizes harmful exhaust emissions, meeting stringent environmental regulations and standards.

The chainsaw also includes an automatic oil pump that ensures a consistent flow of lubrication to the bar and chain, enhancing longevity and reducing wear during use. This feature allows users to focus on their tasks without frequently stopping to manage oil levels.

Additionally, the tool-less chain tensioning system is designed for user convenience, enabling quick adjustments on the fly without needing additional tools. This feature is especially useful for those who are busy or working under time constraints.

Safety is a priority with the Husqvarna 1153136-95, as it comes equipped with a chain brake system designed to stop the chain in the event of a kickback. This important safety feature provides peace of mind for users, especially those new to chainsaw operation.

Overall, the Husqvarna 1153136-95 combines performance, user-friendliness, and advanced technology, rendering it a versatile tool suitable for various cutting tasks. Whether tackling home maintenance or professional projects, this chainsaw is engineered to deliver reliable results and satisfy the demands of users.