Husqvarna 1153136-95 manual Muffler, Starter, Replacing the starter cord

Page 26

MAINTENANCE

Throttle lockout

Make sure the throttle control is locked at the idle setting when the throttle lockout is released. (95)

Press the throttle lockout and make sure it returns to its original position when you release it. (96)

Check that the throttle control and throttle lockout move freely and that the return springs work properly.

(97)

Start the chain saw and apply full throttle. Release the throttle control and check that the chain stops and remains stationary. If the chain rotates when the throttle control is in the idle position you should check the carburetor idle adjustment.

Chain catcher

Check that the chain catcher is not damaged and is firmly attached to the body of the chain saw. (98)

Right hand guard

Check that the right hand guard is not damaged and that there are no visible defects, such as cracks. (11)

Vibration damping system

Regularly check the vibration damping units for cracks or deformation. Make sure the vibration damping units are securely attached to the engine unit and handle unit. (99)

Stop switch

Start the engine and make sure the engine stops when you move the stop switch to the stop setting. (53)

NB! The start/stop switch automatically returns to run position. In order to prevent unintentional starting, the spark plug cap must be removed from the spark plug when assembling, checking and/or performing maintenance.

Muffler

Never use a machine that has a faulty muffler.

Regularly check that the muffler is securely attached to the machine. (100)

Some mufflers are equipped with a special spark arrestor screen. If your machine has this type of muffler, you should clean the screen at least once a week.This is best done with a wire brush. A blocked screen will cause the engine to overheat and may lead to serious damage.

Note! The screen must be replaced if it is damaged. If the screen is blocked the machine will overheat and this will cause damage to the cylinder and piston. Never use a machine with a muffler that is in poor condition. Never use a muffler if the spark arrestor screen is missing or defective. (13)

The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material.

Starter

WARNING! When the recoil spring is

!wound up in the starter housing it is under tension and can, if handled carelessly, pop out and cause personal injury.

Care must be exercised when replacing the return spring or the starter cord. Wear protective glasses and protective gloves.

Replacing the starter cord

Loosen the screws that hold the starter against the crankcase and remove the starter. (101)

Pull out the cord approx. 30 cm (12 inches) and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the pulley rotate slowly backwards. (102)

Undo the bolt in the centre of the pulley and remove the drive disc (A), drive disc spring (B) and the pulley

(C). Insert and secure a new starter cord in the starter pulley. Wind approx. 3 turns of the starter cord on the starter pulley. Fit the starter pulley so that the end of the recoil spring (D) hooks into the starter pulley. Now assemble the drive disc spring, drive disc and the bolt in the centre of the pulley. Carry the starter cord through the hole in the starter housing and the starter handle. Tie a good knot on the starter cord. (103)

26 – English

1153136-95 Rev.2 2010-04-08

Image 26
Contents 445 445e 450 450e 1153136-95 Rev.2 1153136-95 Rev.2 4243 1153136-95 Rev.2 112 113 Decompression valve The valve KEY to SymbolsSymbols on the machine and/or in the manual Contents Dear customer What is what on the chain saw?Introduction General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardChain catcher Stop switchThrottle lockout Right hand guardGeneral rules Cutting equipmentMuffler Cutting equipment designed to reduce kickbackSharpening your chain and adjusting depth gauge setting Tensioning the chainLubricating cutting equipment Needle bearing lubrication Checking wear on cutting equipment445 AssemblyFitting the bar and chain 445e, 450eFuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageStarting Starting and StoppingStarting and stopping StoppingBefore use Basic safety rulesWorking Techniques General working instructionsLimbing Basic cutting techniqueTerms Felling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatFreeing a tree that has fallen badly How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Replacing the starter cord MufflerStarter Lubricating the bar tip sprocket Air filterSpark plug Needle bearing lubricationCooling system Air Injection centrifugal cleaningTemperature -5C 23F or colder Winter useMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data050/1,3 mm Bar and chain combinationsSaw chain filing and file gauges 058/1,5 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsMAINTENANCE, Replacement Repair of EMISSION-RELATED Parts Kickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautions1153136-95 Rev.2 Original instructions 1153136-95

1153136-95 specifications

The Husqvarna 1153136-95 is a high-performance chainsaw designed for ease of use and efficiency, making it an ideal choice for both residential and professional users. Known for its robust build and reliability, this chainsaw is particularly well-suited for tasks such as tree pruning, cutting firewood, and managing landscaping projects.

One of the standout features of the Husqvarna 1153136-95 is its lightweight design. Weighing in at just around 10 lbs, it allows users to easily maneuver during extended periods of operation without causing excessive fatigue. This is complemented by an ergonomic handle that provides a comfortable grip, reducing strain on the hands and wrists.

The chainsaw is powered by an efficient and reliable engine. With a displacement of 38.2 cc, it delivers ample power for most cutting tasks while maintaining fuel efficiency. The technology incorporated into its engine design ensures lower emissions, making it an environmentally friendly option in the category of gas-powered chainsaws.

Another impressive feature of the Husqvarna 1153136-95 is the X-Torq technology. This innovatively engineered system reduces fuel consumption by up to 20%, resulting in longer runtimes between refueling. Additionally, it minimizes harmful exhaust emissions, meeting stringent environmental regulations and standards.

The chainsaw also includes an automatic oil pump that ensures a consistent flow of lubrication to the bar and chain, enhancing longevity and reducing wear during use. This feature allows users to focus on their tasks without frequently stopping to manage oil levels.

Additionally, the tool-less chain tensioning system is designed for user convenience, enabling quick adjustments on the fly without needing additional tools. This feature is especially useful for those who are busy or working under time constraints.

Safety is a priority with the Husqvarna 1153136-95, as it comes equipped with a chain brake system designed to stop the chain in the event of a kickback. This important safety feature provides peace of mind for users, especially those new to chainsaw operation.

Overall, the Husqvarna 1153136-95 combines performance, user-friendliness, and advanced technology, rendering it a versatile tool suitable for various cutting tasks. Whether tackling home maintenance or professional projects, this chainsaw is engineered to deliver reliable results and satisfy the demands of users.