Husqvarna 1153136-95 manual Air filter, Spark plug, Lubricating the bar tip sprocket

Page 27

MAINTENANCE

Tensioning the recoil spring

•Hook the starter cord in the notch in the pulley and turn the starter pulley about 2 turns clockwise.

Note! Check that the pulley can be turned an additional 1/2 turn when the starter cord is pulled all the way out. (104)

Stretch the line with the handle. Move your thumb and release the line. See the figure below. (105)

Replacing the return and drive springs

Recoil spring (A)

•Lift up the starter pulley. See instructions under the heading Changing a broken or worn starter cord. Remember that the recoil spring is coiled under tension in the starter housing.

•Remove the cassette with the recoil spring from the starter.

•Lubricate the recoil spring with light oil. Fit the cassette with recoil spring in the starter. Fit the starter pulley and tension the recoil spring.

Drive disc spring (B)

•Undo the bolt in the centre of the pulley and remove the drive disc and the drive disc spring.

•Replace the drive disc spring and fit the drive disc above the spring. (106)

Fitting the starter

•To fit the starter, first pull out the starter cord and place the starter in position against the crankcase. Then slowly release the starter cord so that the pulley engages with the pawls.

•Fit and tighten the screws that hold the starter.

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

•Carburettor malfunctions

•Starting problems

•Loss of engine power

•Unnecessary wear to engine parts

•Excessive fuel consumption.

•Remove the air filter after taking off the air filter cover. When refitting make sure that the air filter seals tightly against the filter holder. Clean the filter by brushing or shaking it. (107)

The filter can be cleaned more thoroughly by washing it in water and detergent.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter

must always be replaced.

A HUSQVARNA chain saw can be equipped with different types of air filters according to working conditions, weather, season, etc. Contact your dealer for advice.

Spark plug

The spark plug condition is influenced by:

•Incorrect carburetor adjustment.

•An incorrect fuel mixture (too much or incorrect type of oil).

•A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.020 inch (0.5 mm). The spark plug should be replaced after about a month in operation or earlier if necessary. (108)

Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

Lubricating the bar tip sprocket

Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease.

(109)

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regularly.

When lubricating, remove the clutch cover by loosening the two bar nuts. Lay the saw on its side with the clutch drum upwards.

Lubrication involves engine oil dripping into the centre of the clutch drum as it rotates. (110)

1153136-95 Rev.2 2010-04-08

English – 27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents 445 445e 450 450e 1153136-95 Rev.2 1153136-95 Rev.2 4243 1153136-95 Rev.2 112 113 KEY to Symbols Symbols on the machine and/or in the manualDecompression valve The valve Contents What is what on the chain saw? IntroductionDear customer Before using a new chain saw General Safety PrecautionsChain brake and front hand guard Machine′s safety equipmentAlways use common sense Personal protective equipmentRight hand guard Stop switchThrottle lockout Chain catcherCutting equipment designed to reduce kickback Cutting equipmentMuffler General rulesTensioning the chain Sharpening your chain and adjusting depth gauge settingLubricating cutting equipment Checking wear on cutting equipment Needle bearing lubrication445e, 450e AssemblyFitting the bar and chain 445Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageStopping Starting and StoppingStarting and stopping StartingGeneral working instructions Basic safety rulesWorking Techniques Before useBasic cutting technique TermsLimbing Clearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionHow to avoid kickback What is kickback?Freeing a tree that has fallen badly Maintenance Carburetor adjustmentGeneral Muffler StarterReplacing the starter cord Needle bearing lubrication Air filterSpark plug Lubricating the bar tip sprocketWinter use Air Injection centrifugal cleaningTemperature -5C 23F or colder Cooling systemDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical Data058/1,5 mm Bar and chain combinationsSaw chain filing and file gauges 050/1,3 mmYour Warranty Rights and Obligations Federal Emission Control Warranty StatementMAINTENANCE, Replacement Repair of EMISSION-RELATED Parts Other safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautions1153136-95 Rev.2 Original instructions 1153136-95

1153136-95 specifications

The Husqvarna 1153136-95 is a high-performance chainsaw designed for ease of use and efficiency, making it an ideal choice for both residential and professional users. Known for its robust build and reliability, this chainsaw is particularly well-suited for tasks such as tree pruning, cutting firewood, and managing landscaping projects.

One of the standout features of the Husqvarna 1153136-95 is its lightweight design. Weighing in at just around 10 lbs, it allows users to easily maneuver during extended periods of operation without causing excessive fatigue. This is complemented by an ergonomic handle that provides a comfortable grip, reducing strain on the hands and wrists.

The chainsaw is powered by an efficient and reliable engine. With a displacement of 38.2 cc, it delivers ample power for most cutting tasks while maintaining fuel efficiency. The technology incorporated into its engine design ensures lower emissions, making it an environmentally friendly option in the category of gas-powered chainsaws.

Another impressive feature of the Husqvarna 1153136-95 is the X-Torq technology. This innovatively engineered system reduces fuel consumption by up to 20%, resulting in longer runtimes between refueling. Additionally, it minimizes harmful exhaust emissions, meeting stringent environmental regulations and standards.

The chainsaw also includes an automatic oil pump that ensures a consistent flow of lubrication to the bar and chain, enhancing longevity and reducing wear during use. This feature allows users to focus on their tasks without frequently stopping to manage oil levels.

Additionally, the tool-less chain tensioning system is designed for user convenience, enabling quick adjustments on the fly without needing additional tools. This feature is especially useful for those who are busy or working under time constraints.

Safety is a priority with the Husqvarna 1153136-95, as it comes equipped with a chain brake system designed to stop the chain in the event of a kickback. This important safety feature provides peace of mind for users, especially those new to chainsaw operation.

Overall, the Husqvarna 1153136-95 combines performance, user-friendliness, and advanced technology, rendering it a versatile tool suitable for various cutting tasks. Whether tackling home maintenance or professional projects, this chainsaw is engineered to deliver reliable results and satisfy the demands of users.
Top Page Image Contents