Husqvarna 1153136-95 manual Starting and Stopping, Starting and stopping, Cold engine

Page 20

STARTING AND STOPPING

Starting and stopping

WARNING! Note the following before

!starting:

The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting.

Never start a chain saw unless the bar, chain and all covers are fitted correctly. Otherwise the clutch can come loose and cause personal injuries.

Place the machine on firm ground. Make sure you have a secure footing and that the chain cannot touch anything.

Keep people and animals well away from the working area.

Never wrap the starter cord around your hand.

Starting

The chain brake should be activated when starting the chain saw. Activate the chain brake by pushing the front hand guard forwards. (49)

Cold engine

Start position, 1: Set the start/stop switch in the choke position by pulling the red control outward - upward. (50) Decompression valve (2): Press the valve to reduce the pressure in the cylinder and make starting easier. Once the machine has started the valve will automatically return to its original setting. (50)

Air purge (3): Press the air purge diaphragm repeatedly until fuel fills the diaphragm (at least 6 times). The diaphragm need not be completely filled. (50)

Grip the front handle with your left hand. Hold the chain saw on the ground by placing your right foot through the rear handle. (51)

Pull the starter handle, 4: Pull the starter handle with your right hand and pull out the starter cord slowly until you feel a resistance (as the starter pawls engage) then pull firmly and rapidly until the engine fires.

Push down the red choke control, 5: As soon as the engine fires which can be heard through a "puff" sound, push down on the red choke control.

Pull the starter handle (6): Keep on pulling the cord powerfully until the engine starts.

Warm engine

Start position, 1: The correct choke/start throttle setting for warm starting is obtained by initially moving the choke control by pulling the red control outward - upwards. (50) Decompression valve (2): Press the valve to reduce the pressure in the cylinder and make starting easier. Once the machine has started the valve will automatically return to its original setting. (50)

Air purge (3): Press the air purge diaphragm repeatedly until fuel fills the diaphragm (at least 6 times). The diaphragm need not be completely filled. (50)

20 – English

Push down the red choke control, 5: This inactivates the choke, which is not needed when starting a warm chain saw. However the movement of the start/stop switch will have engaged a high idle, making warm starting easier.

Pull the starter handle, 6: Grip the front handle with your left hand. Hold the chain saw on the ground by placing your right foot through the rear handle. (51)

Pull the starter handle with your right hand and pull out the starter cord slowly until you feel a resistance (as the starter pawls engage) then pull firmly and rapidly until the engine fires.

As the chain brake is still engaged the speed of the engine must be set to idling as soon as possible, this is achieved by disengaging the throttle lock. Disengagement is done by gently touching on the throttle trigger. This prevents unnecessary wear to the clutch, clutch drum and brake band. Allow the machine to idle a few seconds before giving full throttle.

There is a simplified start reminder with illustrations to describe each step on the rear edge of the saw (A). (50) NB! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine.

Note! Pull the front hand guard towards the front handle. The chain brake is now disengaged. Your saw is ready for use.

WARNING! Long term inhalation of the

! engine’s exhaust fumes, chain oil mist and dust from sawdust can represent a health risk.

• Never start a chain saw unless the bar, chain and all covers are fitted correctly. See instructions under the heading Assembly. Without a bar and chain attached to the chain saw the clutch can come loose and cause serious injury.

• The chain brake should be activated when starting. Se instructions under the heading Start and stop. Do not drop start. This method is very dangerous because you may lose control of the saw. (52)

• Never start the machine indoors. Exhaust fumes can be dangerous if inhaled.

• Observe your surroundings and make sure that there is no risk of people or animals coming into contact with the cutting equipment.

• Always hold the saw with both hands. The right hand should be on the rear handle, and the left hand on the front handle. All people, whether right or left handed, should use this grip. Use a firm grip with thumbs and fingers encircling the chain saw handles.

Stopping

Stop the engine by pushing the start/stop switch down. (53)

NB! The start/stop switch automatically returns to run position. To avoid involuntary start up, the spark plug cap must always be removed from the spark plug when the machine is unsupervised. (54)

1153136-95 Rev.2 2010-04-08

Page 19 Page 21
Image 20
Page 19 Page 21
Contents 445 445e 450 450e 1153136-95 Rev.2 1153136-95 Rev.2 4243 1153136-95 Rev.2 112 113 Decompression valve The valve KEY to SymbolsSymbols on the machine and/or in the manual Contents Dear customer What is what on the chain saw?Introduction General Safety Precautions Before using a new chain sawMachine′s safety equipment Always use common sensePersonal protective equipment Chain brake and front hand guardStop switch Throttle lockoutChain catcher Right hand guardCutting equipment MufflerGeneral rules Cutting equipment designed to reduce kickbackSharpening your chain and adjusting depth gauge setting Tensioning the chainLubricating cutting equipment Needle bearing lubrication Checking wear on cutting equipmentAssembly Fitting the bar and chain445 445e, 450eFuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingStarting StoppingBasic safety rules Working TechniquesBefore use General working instructionsLimbing Basic cutting techniqueTerms Tree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatFreeing a tree that has fallen badly How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Replacing the starter cord MufflerStarter Air filter Spark plugLubricating the bar tip sprocket Needle bearing lubricationAir Injection centrifugal cleaning Temperature -5C 23F or colderCooling system Winter useMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gauges050/1,3 mm 058/1,5 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsMAINTENANCE, Replacement Repair of EMISSION-RELATED Parts American Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautions1153136-95 Rev.2 Original instructions 1153136-95

1153136-95 specifications

The Husqvarna 1153136-95 is a high-performance chainsaw designed for ease of use and efficiency, making it an ideal choice for both residential and professional users. Known for its robust build and reliability, this chainsaw is particularly well-suited for tasks such as tree pruning, cutting firewood, and managing landscaping projects.

One of the standout features of the Husqvarna 1153136-95 is its lightweight design. Weighing in at just around 10 lbs, it allows users to easily maneuver during extended periods of operation without causing excessive fatigue. This is complemented by an ergonomic handle that provides a comfortable grip, reducing strain on the hands and wrists.

The chainsaw is powered by an efficient and reliable engine. With a displacement of 38.2 cc, it delivers ample power for most cutting tasks while maintaining fuel efficiency. The technology incorporated into its engine design ensures lower emissions, making it an environmentally friendly option in the category of gas-powered chainsaws.

Another impressive feature of the Husqvarna 1153136-95 is the X-Torq technology. This innovatively engineered system reduces fuel consumption by up to 20%, resulting in longer runtimes between refueling. Additionally, it minimizes harmful exhaust emissions, meeting stringent environmental regulations and standards.

The chainsaw also includes an automatic oil pump that ensures a consistent flow of lubrication to the bar and chain, enhancing longevity and reducing wear during use. This feature allows users to focus on their tasks without frequently stopping to manage oil levels.

Additionally, the tool-less chain tensioning system is designed for user convenience, enabling quick adjustments on the fly without needing additional tools. This feature is especially useful for those who are busy or working under time constraints.

Safety is a priority with the Husqvarna 1153136-95, as it comes equipped with a chain brake system designed to stop the chain in the event of a kickback. This important safety feature provides peace of mind for users, especially those new to chainsaw operation.

Overall, the Husqvarna 1153136-95 combines performance, user-friendliness, and advanced technology, rendering it a versatile tool suitable for various cutting tasks. Whether tackling home maintenance or professional projects, this chainsaw is engineered to deliver reliable results and satisfy the demands of users.
Top Page Image Contents