Husqvarna 1151187-95 manual Low speed jet L, Fine adjustment of the idle speed T, High speed jet H

Page 30

MAINTENANCE

Low speed jet L

Try to find the highest idling speed, turning the low speed needle L clockwise respectively counter-clockwise. When the highest speed has been found, turn the low speed needle L 1/4 turn counter-clockwise.

+ 1/4

L

CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti-clockwise until the cutting attachment stops.

Fine adjustment of the idle speed T

Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops. The idle speed is correctly adjusted when the engine will run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts to rotate.

WARNING! If the idle speed cannot be

! adjusted so that the cutting attachment stops, contact your dealer/service workshop. Do not use the machine until it has been correctly adjusted or repaired.

High speed jet H

The high speed jet H affects the engine power, speed, temperature and fuel consumption. If the high speed jet H is set too lean (screwed in too far) the engine speed will be too high and cause engine damage. Do not let the engine run at full speed for more than 10 seconds.

Note that the engine should not be under load when you adjust the high speed jet H. You should therefore remove the cutting attachment, nut, support flange and drive disc before adjusting the high speed jet H.

Apply full throttle and turn the high speed jet H very slowly clockwise until the engine slows down. Then turn the high speed jet H very slowly anticlockwise until the engine starts to run unevenly. Now turn the high speed jet H slowly clockwise a little way until the engine runs smoothly.

H

CAUTION! For optimum adjustment of the carburettor, contact a qualified dealer/service workshop that has a revolution counter at their disposal.

Correctly adjusted carburetor

When the carburetor is correctly adjusted the machine will accelerate without hesitation and burble a little at maximum speed. It is also important that the cutting attachment does not rotate at idle. If the low speed jet L is set too lean it may cause starting difficulties and poor acceleration.

If the high speed jet H is set too lean it will result in less power, less performance, poor acceleration and/or damage to the engine.

If both the L and H jets are set too rich it will results in acceleration problems or too low a working speed.

30 – English

Page 29 Page 31
Image 30
Page 29 Page 31
Contents 232R 235R 235FR Operator of the machine must Ensure, while working, that no KEY to SymbolsSymbols Persons or animals come closer thanContents Introduction Dear customerWhat is WHAT? What is what?General Safety Precautions Personal protective equipmentMachine′s safety equipment Throttle lockoutVibration damping system Stop switchCutting attachment guard Quick releaseMuffler Locking nutCutting equipment Cutting equipmentGeneral rules Sharpening grass cutters and grass blades Sharpening the saw bladeTrimmer head Assembly Fitting the handlebar 232RFitting the handlebar 235R, 235FR Transport position, handlebar Assembling the cutting equipmentFitting a blade guard, grass blade and grass cutter 232R Fitting the blade guard and saw blade 232R Fitting the blade guard and saw blade 235R, 235FR Fitting a trimmer guard and Superauto II 1 trimmer head 232R Fitting other guards and cutting attachments 235R, 235FR AM LCorrect height Adjusting the harness and clearing sawSpreading the load on your shoulders Correct balanceFuel safety Fuel HandlingFuel Fueling MixingStarting and stopping Starting and StoppingCheck before starting Cold engineFor throttle handles with a start throttle lock Warm engineStarting StoppingBasic safety rules Working TechniquesGeneral working instructions ABC of clearing Forestry clearing using a saw blade Grass trimming with a trimmer head Grass clearing using a grass bladeBrush cutting with a saw blade TrimmingCutting SweepingMaintenance CarburetorLow speed jet L Fine adjustment of the idle speed TCorrectly adjusted carburetor High speed jet HCooling system Adjusting the start throttle speedMuffler Remember the risk of fireAir filter Cleaning the air filterBevel gear Spark plugMaintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataApproved accessories 232R Type Approved accessories 235R, 235FR TypeFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsMAINTENANCE, Replacement Repair of EMISSION-RELATED Parts Super Auto Super Auto II Page T35, T35x Trimmy Hit Trimmy Hit Pro Trimmy SII Page S35 2,7mm 095-.106 25 m 15 cm T45, T45x Page Page Page Page 1151187-95

1151187-95 specifications

The Husqvarna 1151187-95 is a robust and reliable accessory designed to enhance the efficiency and functionality of Husqvarna outdoor power equipment. As part of a well-regarded brand known for its high-quality and durable tools, this model embodies advanced engineering and innovative features that cater to the needs of both professionals and homeowners alike.

One of the standout characteristics of the Husqvarna 1151187-95 is its ergonomic design, which ensures ease of use and comfort during operation. The user-friendly interface allows for quick adjustments and features that minimize fatigue, making long hours of work less daunting. The lightweight construction of this model adds to its portability, allowing users to transport and store the tool with ease.

The technology embedded in the Husqvarna 1151187-95 is noteworthy. It incorporates advanced vibration dampening, which significantly reduces the stress and strain on the user's hands and arms during prolonged usage. This feature not only enhances comfort but also promotes safety, enabling users to maintain better control of the equipment.

In addition to its ergonomic benefits, this model is built with durability in mind. The materials used in the construction of the Husqvarna 1151187-95 are designed to withstand harsh outdoor conditions, ensuring longevity and reliable performance in various environments. This robust build quality means that users can trust this tool to perform consistently and effectively over time.

Moreover, the Husqvarna 1151187-95 is compatible with a range of other Husqvarna products, creating flexibility for users who may own multiple tools. This interoperability streamlines the maintenance process, allowing users to switch between different attachments or components seamlessly.

In summary, the Husqvarna 1151187-95 combines ergonomic design, advanced technology, and durable construction to deliver a high-performance solution for outdoor work. Whether you are a landscaping professional or a weekend warrior, this tool is designed to enhance your efficiency and help you achieve exceptional results in your outdoor projects. Its emphasis on comfort and durability makes the Husqvarna 1151187-95 an excellent investment for anyone seeking reliable outdoor power equipment.
Top Page Image Contents