Husqvarna 1151187-95 manual Bevel gear, Air filter, Spark plug, Cleaning the air filter

Page 32

MAINTENANCE

4 Cylinder cover (directs cold air over the cylinder).

Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder.

Bevel gear

The bevel gear is filled with the right quantity of grease at the factory. However, before using the machine you should check that the bevel gear is filled three-quarters full with grease. Use HUSQVARNA special grease.

The grease in the bevel gear does not normally need to be changed except if repairs are carried out.

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

•Carburettor malfunctions

•Starting problems

•Loss of engine power

•Unnecessary wear to engine parts

•Excessive fuel consumption.

Clean the filter every 25 hours, or more regularly if conditions are exceptionally dusty.

Cleaning the air filter

Remove the air filter cover and take out the filter. Wash it clean in warm, soapy water. Ensure that the filter is dry before refitting it.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter

must always be replaced.

If the machine is used in dusty conditions the air filter should be soaked in oil. See instructions under the heading Oiling the air filter.

Oiling the air filter

Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.

Put the filter in a plastic bag and pour the filter oil over it. Knead the plastic bag to distribute the oil. Squeeze the excess oil out of the filter inside the plastic bag and pour off the excess before fitting the filter to the machine. Never use common engine oil. This would drain through the filter quite quickly and collect in the bottom.

Spark plug

The spark plug condition is influenced by:

•Incorrect carburetor adjustment.

•An incorrect fuel mixture (too much or incorrect type of oil).

•A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.020 inch (0.5 mm). The spark plug should be replaced after about a month in operation or earlier if necessary.

CAUTION! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/ cylinder. Check that the spark plug is fitted with a suppressor.

Note: Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically recommended by HUSQVARNA.

32 – English

Page 31 Page 33
Image 32
Page 31 Page 33
Contents 232R 235R 235FR KEY to Symbols SymbolsOperator of the machine must Ensure, while working, that no Persons or animals come closer thanContents Introduction Dear customerWhat is WHAT? What is what?General Safety Precautions Personal protective equipmentMachine′s safety equipment Throttle lockoutStop switch Cutting attachment guardVibration damping system Quick releaseMuffler Locking nutGeneral rules Cutting equipmentCutting equipment Sharpening grass cutters and grass blades Sharpening the saw bladeTrimmer head Fitting the handlebar 235R, 235FR AssemblyFitting the handlebar 232R Fitting a blade guard, grass blade and grass cutter 232R Transport position, handlebarAssembling the cutting equipment Fitting the blade guard and saw blade 232R Fitting the blade guard and saw blade 235R, 235FR Fitting a trimmer guard and Superauto II 1 trimmer head 232R Fitting other guards and cutting attachments 235R, 235FR AM LAdjusting the harness and clearing saw Spreading the load on your shouldersCorrect height Correct balanceFuel Fuel safetyFuel Handling Fueling MixingStarting and Stopping Check before startingStarting and stopping Cold engineWarm engine StartingFor throttle handles with a start throttle lock StoppingGeneral working instructions Basic safety rulesWorking Techniques ABC of clearing Forestry clearing using a saw blade Grass clearing using a grass blade Brush cutting with a saw bladeGrass trimming with a trimmer head TrimmingCutting SweepingMaintenance CarburetorFine adjustment of the idle speed T Correctly adjusted carburetorLow speed jet L High speed jet HAdjusting the start throttle speed MufflerCooling system Remember the risk of fireCleaning the air filter Bevel gearAir filter Spark plugMaintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataApproved accessories 232R Type Approved accessories 235R, 235FR TypeFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsMAINTENANCE, Replacement Repair of EMISSION-RELATED Parts Super Auto Super Auto II Page T35, T35x Trimmy Hit Trimmy Hit Pro Trimmy SII Page S35 2,7mm 095-.106 25 m 15 cm T45, T45x Page Page Page Page 1151187-95

1151187-95 specifications

The Husqvarna 1151187-95 is a robust and reliable accessory designed to enhance the efficiency and functionality of Husqvarna outdoor power equipment. As part of a well-regarded brand known for its high-quality and durable tools, this model embodies advanced engineering and innovative features that cater to the needs of both professionals and homeowners alike.

One of the standout characteristics of the Husqvarna 1151187-95 is its ergonomic design, which ensures ease of use and comfort during operation. The user-friendly interface allows for quick adjustments and features that minimize fatigue, making long hours of work less daunting. The lightweight construction of this model adds to its portability, allowing users to transport and store the tool with ease.

The technology embedded in the Husqvarna 1151187-95 is noteworthy. It incorporates advanced vibration dampening, which significantly reduces the stress and strain on the user's hands and arms during prolonged usage. This feature not only enhances comfort but also promotes safety, enabling users to maintain better control of the equipment.

In addition to its ergonomic benefits, this model is built with durability in mind. The materials used in the construction of the Husqvarna 1151187-95 are designed to withstand harsh outdoor conditions, ensuring longevity and reliable performance in various environments. This robust build quality means that users can trust this tool to perform consistently and effectively over time.

Moreover, the Husqvarna 1151187-95 is compatible with a range of other Husqvarna products, creating flexibility for users who may own multiple tools. This interoperability streamlines the maintenance process, allowing users to switch between different attachments or components seamlessly.

In summary, the Husqvarna 1151187-95 combines ergonomic design, advanced technology, and durable construction to deliver a high-performance solution for outdoor work. Whether you are a landscaping professional or a weekend warrior, this tool is designed to enhance your efficiency and help you achieve exceptional results in your outdoor projects. Its emphasis on comfort and durability makes the Husqvarna 1151187-95 an excellent investment for anyone seeking reliable outdoor power equipment.
Top Page Image Contents