Hustler Turf 928192 Engine starting, Stopping the engine, Moving tractor with stalled engine

Page 15

Deck lift

pedal

Figure 3-4

5.With the deck clutch switch up and/or the control levers in the neutral position, slowly raise off of the seat. The engine should stop.

6.If the engine fails to stop when the deck clutch switch is up or one or both of the control levers is up and the operator is off the seat, check the function of the seat switch. If the seat switch is not operating properly (is not opening or closing) and if the cause can not be determined, replace the seat switch.

If the problem can not be located, contact your Hustler Dealer.

WARNING: The safety interlock system should always function per steps 4 and 5. If it does not function properly, it should be corrected immediately. Do not operate machine without properly functioning seat safety switch.

Engine starting

The tractor’s safety start interlock system is also designed to protect the operator and others from accidental injury due to unintentional engine starting. The engine starting motor will not engage until:

A.Control levers are in the park brake position.

B.Deck clutch switch is in the down (OFF) position.

WARNING: The safety interlock system must not be disconnected or bypassed. Doing so could cause the machine to operate unexpectedly resulting in personal injury.

NOTE: The operator’s seat is equipped with a separate safety switch. If for any reason the operator should become unseated when the control levers are not in the park brake position (park brake switches are disengaged) or the deck clutch switch is engaged the engine will stop.

The following steps are the correct procedures for starting the engine. If difficulty is encountered, contact the Hustler Dealer in your area.

1.Before starting tractor each day, perform daily pre-operation checking. (See Safety start interlock system section)

2.Make sure the control levers are in the park brake position and deck clutch switch is disengaged. Only start the engine from the operator’s position.

3.Use choke, if unit is equipped with one, when engine is cold, or if warm engine fails to start within 5 seconds of cranking. Avoid flooding and operate engine without choking as soon as possible.

4.Set throttle at approximately 1/2 open position.

5.Insert key in ignition switch and rotate full clockwise to engage starting motor. Release key when engine starts.

IMPORTANT: The engine starter should not be operated for periods longer than 30 seconds at a time. An interval of at least two minutes should be allowed between such cranking periods to protect the starter from overheating and burn-out.

6.Perform test to make sure safety start interlock system is operating properly. Refer to Safety start interlock system section.

7.As soon as engine begins to run, check to make certain the oil warning light, check engine light and alternator warning light (if applicable) are off. If not, stop engine immediately and check for

Slot

Bypass valve rod (Left rod shown)

(viewed from the rear left underneath side)

Figure 3-5A

Bypass valve rod (Left rod shown)

Bypass valve rod shown in towing position

Figure 3-5B

the cause.

8.Allow the engine to idle a few minutes before advancing the throttle and/or engaging the deck clutch.

Stopping the engine

Use the following procedure to shut off the engine after operating the equipment.

1.Place the control levers in the park brake position

2.Disengage the deck clutch

3.Throttle back to low idle for a couple of minutes

4.Rotate ignition key counter-clockwise to the OFF position. Remove the key from switch before leaving the tractor.

Moving tractor with stalled engine

If it becomes necessary to move the tractor when the engine is inoperative, the transaxles are equipped with bypass valves.

WARNING: Allow engine exhaust manifold to cool before engaging or disengaging the bypass valves. The bypass valve rods are located close to the exhaust system.

Mini Z 36/42 units produced prior to and including serial number 06120544 - Before moving the unit, pull out on the bypass valve rods and slide them into the slot to lock in position.

Both bypass valve rods are located underneath the rear of the tractor at the back of the transaxle. Fig. 3-5A

The control levers must be placed in the neutral position, to release the park brakes, so that the tractor can be moved.

14

107708_0808

Image 15
Contents Hustler Mini Z FasTrak Super Duty 36/42 General Information 1077080808 What is Covered by this Warranty Limitation of Remedies What is Covered by this Warranty Time Limits Safety Precautions Safety and Instruction Decals Slope Guide 1077080808 Operation Using a rampOperation Safe Operating PracticesDo not operate on slopes greater than 15 degrees ChildrenControl Lever Shown with control levers Neutral position Safety start interlock systemControl Panel ControlsEngine starting Stopping the engineMoving tractor with stalled engine Driving the tractor Operating suggestionsSide discharge Chute Step Neutral Right control leverThree point turn StepDeck cutting height adjustment Mower deck operationAnti-scalp wheels 1077080808 Maintenance & Adjustments ZT 2800 integrated Pump/motor Expansion tank Filter LubricationElectrical system Hydraulic systemApproved filter element only Fuel systemEngine oil and filter Engine air filterMower blade maintenance General engine maintenance BeltsSeat adjustment Control lever adjustmentMower blade removal Refer to Fig Viewed from top of unit 1077080808 Troubleshooting 1077080808 New season preparation StorageProduct Literature Preparation of engine for storage1077080808 Moving tractor with stalled engine Index1077080808 Hustler Turf Equipment