Hustler Turf Super Duty 42, Super 928192 Right control lever, Three point turn, Step Neutral

Page 17

maneuvers to become familiar with the operation of the equipment before attempting normal speed operation. An inexperienced operator should not mow on slopes or on uneven terrain.

WARNING: If you lose steering control while operating the machine, place the steering control levers in the park brake position immediately. Inspect the machine and involve your Hustler dealer to resolve the problem before continuing to operate.

WARNING: The unit’s steering control levers are very

responsive: Easy does it! For smooth operation, move lever slowly, avoid sudden movement. Skill and ease of operation come with practice and experience. The machine can spin very rapidly. Use caution when making turns and slow down before making sharp turns.

Inexperienced operators may have a tendency to oversteer and lose control. Slow-moving practice maneuvers are recommended to become familiar with these characteristics before attempting normal speed operation.

WARNING: Sharp depressions or raised obstacles (such as gutters or curbs) should not be directly approached at high speed in an attempt to “jump” them as the operator could be thrown from the equipment. Approach at a slow speed and angle one drive wheel at the obstruction. Continue at an angle until the wheel clears and then pivot the opposite wheel around.

When turning on soft wet turf, keep both wheels rolling either forward or backward. Pivoting on one stopped wheel can damage turf. This is especially important when mowing.

Tractor performance is maximum when the throttle is set at full rpm. This gives maximum power to the drive wheels and deck when needed. Use the control levers to control ground speed rather than engine rpm.

Keep blades sharp. Many professional mowing companies have additional sets of blades and change blades twice a day: once in the morning and again at noon. Many problems with incorrect cutting patterns are due to dull blades or blades which have been sharpened incorrectly. Information on sharpening blades is listed in this manual’s maintenance section. In addition, most communities have individuals or companies which specialize in sharpening mower blades. Blade sharpness

should be checked daily.

DANGER: Never work with blades while engine is running or deck clutch switch is engaged (on). Always place deck clutch switch in the disengaged position, place control levers in the park brake position and turn engine off and disconnect negative battery cable. Block up mower when you must work under it. Wear gloves when handling blades. Always check for blade damage if mower strikes rock, branch or other foreign object during mowing!

Use high blade speed. Your mower is designed to operate at full throttle. The throttle setting directly controls blade speed. The highest blade speed generally gives best cut.

Direct grass discharge to right, away from unmown area. Select a mowing pattern that directs grass discharge towards the outside, not towards center, of mowing area. Generally, this means using a pattern utilizing left turns because side discharge is to right. In any case, avoid throwing grass discharge onto unmowed area because grass is then mowed “twice”. Mowing twice puts an unnecessary load on the unit and reduces mowing efficiency.

When mowing a lawn for the first time cut grass slightly longer than normal to avoid scalping uneven terrain. When possible, it is best to use the cutting height that was used in the past. When cutting grass taller than six inches, you may want to mow the lawn twice to achieve a better quality of cut.

During normal mowing cut only about 1/3 of the grass blade.

Three point turn

 

Left

 

control

Step 1

lever

 

Right control lever

Neutral

 

lever control Left

Neutral

 

 

Step 2

 

 

 

 

 

 

lever control Right

Step 3

Neutral

Right control lever

Left control lever

Figure 3-8

16

107708_0808

Image 17
Contents Hustler Mini Z FasTrak Super Duty 36/42 General Information 1077080808 What is Covered by this Warranty Limitation of Remedies What is Covered by this Warranty Time Limits Safety Precautions Safety and Instruction Decals Slope Guide 1077080808 Operation Using a rampSafe Operating Practices OperationDo not operate on slopes greater than 15 degrees ChildrenControl Panel Safety start interlock systemControls Control Lever Shown with control levers Neutral positionMoving tractor with stalled engine Engine startingStopping the engine Side discharge Chute Driving the tractorOperating suggestions Three point turn Right control leverStep Step NeutralAnti-scalp wheels Deck cutting height adjustmentMower deck operation 1077080808 Maintenance & Adjustments Electrical system LubricationHydraulic system ZT 2800 integrated Pump/motor Expansion tank FilterEngine oil and filter Fuel systemEngine air filter Approved filter element onlyMower blade maintenance General engine maintenance BeltsMower blade removal Seat adjustmentControl lever adjustment Refer to Fig Viewed from top of unit 1077080808 Troubleshooting 1077080808 Product Literature StoragePreparation of engine for storage New season preparation1077080808 Moving tractor with stalled engine Index1077080808 Hustler Turf Equipment