Husqvarna 1150901-95 manual Fueling, Fuel safety, Transport and storage, Long-term storage

Page 19

FUEL HANDLING

•Never use waste oil. This results in damage to the oil pump, the bar and the chain.

•It is important to use oil of the right grade (suitable viscosity range) to suit the air temperature.

•In temperatures below 32°F (0°C) some oils become too viscous. This can overload the oil pump and result in damage to the oil pump components.

•Contact your service agent when choosing chain oil.

Fueling

WARNING! Taking the following

!precautions, will lessen the risk of fire:

Do not smoke and do not place any hot objects in the vicinity of fuel.

Always stop the engine and let it cool for a few minutes before refuelling.

When refuelling, open the fuel cap slowly so that any excess pressure is released gently.

Tighten the fuel cap carefully after refuelling.

Always move the machine away from the refuelling area before starting.

Clean the area around the fuel cap. Clean the fuel and chain oil tanks regularly. The fuel filter must be replaced at least once a year. Contamination in the tanks causes malfunction. Make sure the fuel is well mixed by shaking the container before refuelling.The capacities of the chain oil tank and fuel tank are carefully matched. You should therefore always fill the chain oil tank and fuel tank at the same time.

WARNING! Fuel and fuel vapor are

! highly flammable. Take care when handling fuel and chain oil. Be aware of the risks of fire, explosion and those associated with inhalation.

Fuel safety

•Never refuel the machine while the engine is running.

•Make sure there is plenty of ventilation when refuelling or mixing fuel (gasoline and 2-stroke oil).

•Move the machine at least 10 ft (3 m) from the refuelling point before starting it.

•Never start the machine:

1If you have spilled fuel or chain oil on the machine. Wipe off the spillage and allow remaining fuel to evaporate.

2If you have spilled fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use soap and water.

3If the machine is leaking fuel. Check regularly for leaks from the fuel cap and fuel lines.

WARNING! Never use a machine with

! visible damage to the spark plug guard and ignition cable. A risk of sparking arises, which can cause a fire.

Transport and storage

•Always store the chain saw and fuel so that there is no risk of leakages or fumes coming into contact with sparks or naked flames from electrical equipment, electric motors, relays/switches, boilers and the like.

•Always store fuel in an approved container designed for that purpose.

•For longer periods of storage or for transport of the chain saw, the fuel and chain oil tanks should be emptied. Ask where you can dispose of waste fuel and chain oil at your local gas station.

•Ensure the machine is cleaned and that a complete service is carried out before long-term storage.

•The bar guard must always be fitted to the cutting attachment when the machine is being transported or in storage, in order to prevent accident contact with the sharp chain. Even a non-moving chain can cause serious cuts to yourself or persons you bump into with an exposed chain.

Long-term storage

Empty the fuel/oil tanks in a well ventilated area. Store the fuel in approved cans in a safe place. Fit the bar guard. Clean the machine. See instructions under the heading Maintenance schedule.

English – 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents
Operator’s manual 357XP EPA I 359 EPA Symbols on the machine KEY to SymbolsSymbols in the operator’s manual EPA Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufflerBar Cutting equipment designed to reduce kickbackChain General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain Filling with chain oil Lubricating cutting equipmentChecking chain lubrication Needle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyWorking with the chain Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Terms Basic cutting techniqueLimbing Clearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionDirectional cuts FellingFelling cut Freeing a trapped tree Freeing a tree that has fallen badlyCutting trees and branches that are in tension Cutting the trunk into logs How to avoid kickbackWhat is kickback? General adviceCarburetor adjustment MaintenanceGeneral High speed jet H Correctly adjusted carburetorImmediately Checking the brake triggerMuffler Changing a broken recoil spring StarterChanging a broken or worn starter cord Tensioning the recoil springFitting the starter Air filterSpark plug Lubricating the bar tip sprocketNeedle bearing lubrication Adjustment of the oil pumpAir Injection centrifugal cleaning When making adjustmentsElectrical carburetor heating Temperature 0C 32F or colderWinter use Heated handlesDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical Data050 Bar and chain combinations058 Saw chain filing and file gauges Repair or Replacement of Parts Repair or Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautions1150901-95